Frame Memory Operations - Sony XKS-C9111 User Manual

To check the assignment status details of each resource,
press [Detail] in the Resource Share menu (7312.1) to
display the Detail menu (7312.2). The details for the
resource selected in the upper list in the status area are
displayed.
Setup menu operation
[SWR1] displayed in the Setup menu refers to logical
switcher 1, and [SWR2] refers to logical switcher 2. These
can be configured in the same way as the physical
switcher.
The resource numbers for the logical switchers and
physical switcher are also displayed in the input/output
display in the following menus.
• Engineering Setup >Switcher >Input menu (7332)
• Engineering Setup >Switcher >Output menu (7333)
• Engineering Setup >Switcher >Output >Output Assign
menu (7333.1)
However, only physical switcher resource numbers are
displayed for XVS-9000 outputs 81 to 96 (multi viewer
outputs 1 to 16).
Notes
• Changing the signal format in the Engineering Setup
>System >Format menu (7313) may also change the
setting of the other logical switcher.
- If the combination of signal formats that would result
from changing signal format is not supported for
resource sharing, the other logical switcher is set to the
same format as the currently selected logical switcher,
and reboots.
- If the field frequency/frame frequency is changed, the
other logical switcher also changes in conjunction with
the currently selected logical switcher, and reboots.
- If the input reference signal is changed, the other
logical switcher also changes in conjunction with the
currently selected logical switcher.
• The Engineering Setup >System >Start Up menu (7314)
[Resume FM Status] and [Init Status with FM] settings
are disabled.
• Executing [Reset] in the Engineering Setup >System
>Initialize menu (7315) will reset both logical switchers
1 and 2, regardless of which logical switcher is currently
selected. Executing [All Clear] will initialize the
currently selected logical switcher and reset the other
logical switcher.
• When installing software using the Engineering Setup
>System >Install/Unit Config >Install menu (7316.10),
the other logical switcher cannot be operated.
• The following menus can be configured only from
logical switcher 1. All inputs and outputs are the target
of settings, regardless of the resource assignments.
- Engineering Setup >System >Network Config >Net
I/F Initialize menu (7311.1)
- Engineering Setup >System >Network Config >IP
Address menu (7311.2)
- Engineering Setup >System >Network Config >Net
I/F Protocol menu (7311.3)
- Engineering Setup >System >Network Config >FEC
menu (7311.4)
- Engineering Setup >System >Network Config >Input/
Output menu (7311.5)
- Engineering Setup >System >Network Config
>Genlock menu (7311.6)
- Engineering Setup >System >Network Config
>NMOS menu (7311.7)
- Engineering Setup >System >Maintenance >SDI
Output Enable menu (7317.3)
• The reference phase (System Phase) setting in the
Engineering Setup >Switcher >Config menu (7331) is
common to logical switchers 1 and 2.
• Setup menu operation for shared resources is available
from logical switcher 1 only.
However, Engineering Setup >Panel >Xpt Assign >Src
Name/Src Color menu (7322.6) independent operation
for shared resources is available on logical switchers 1
and 2.

Frame Memory Operations

Frame memory data
The image data (folders/files) that can be used by each
logical switcher varies depending on the frame memory
folder mode setting.
Shared mode
All frame memory data is shared between logical switchers
1 and 2.
All folders and files are displayed as the target for
operations in the menu for each logical switcher.
Notes
• When the signal formats of logical switchers 1 and 2 are
different and Dual Simul mode is enabled, shared mode
cannot be used.
• When an FM output is locked on either logical switcher,
file operations on the file loaded in the locked FM output
are not available from the other logical switcher.
• The following operations are available on either logical
switcher for a file loaded in an FM output on the other
logical switcher.
Copy, move, delete, rename, Couple function, Separate
function, trim, and unload (remove from memory)
• The folder lock/unlock settings are linked on logical
switchers 1 and 2.
Dedicated mode
When a switcher is started with resource sharing enabled,
dedicated folders with the following names are created for
each logical switcher.
• Logical switcher 1: !L_SWR1
210