Sony XKS-C9111 User Manual page 112

No. Parameter Adjustment
1 Luminance Luminance
2 Saturation Saturation
3 Hue Hue
5
In the <Key Source> group, specify the key source
selection mode.
Self: Selects the key fill bus signal.
Auto Select: Automatically selects the key fill signal
on the cross-point buttons and the signal assigned
with it as a pair.
Split: Allows you to select a separate signal that the
signal that would be selected automatically.
Notes
• When chroma key is selected as the key type, select
[Self].
• When [Split] is selected, the key memory function is
disabled.
6
If [Split] is selected in step 5, select a key source signal
using one of the following methods.
• On the cross-point control block, press and hold
delegation button [KEY1] on the cross-point pad
and select a signal using the cross-point buttons in
the 2nd row.
• Press and hold the [SPLT] button in the key control
block, then select a signal using the cross-point
buttons in the 2nd row in the cross-point control
block.
• On the Flexi Pad control block in key operation
mode, press and hold the [KEY1] button in the
memory recall section and select a signal using the
cross-point buttons in the 2nd row in the cross-point
control block.
• On the cross-point control block in key/AUX bus
delegation mode, press and hold the [KEY1] button
in the 1st row and select a signal using the cross-
point buttons in the 2nd row.
When a cross-point button is pressed, a key signal is
selected.
To select a video signal, first set the [KEY] button
operation mode in the Setup menu (see page 112).
Notes
• On the cross-point control block in key bus mode or
free assign mode, you can select a key fill signal in
the 1st row and a key source signal in the 2nd row by
pressing and holding the following buttons.
- Key bus delegation buttons on the cross-point pad
- [SPLT] button on the key control block
- Key delegation buttons in the memory recall
section on the Flexi Pad control block (key
operation mode)
• You can assign a key source bus delegation button to
the 1st row or 2nd row of the AUX bus control block
(AUX bus operation mode) in the Setup menu (see
page 418).
To select a video signal assigned to a cross-point
button
Set the operation mode that allows you to select both a key
signal and a video signal using the [KEY] button in the
Setup menu (see page 431).
This allows you to select a key signal and video signal
using the following methods.
• To select a key signal on the cross-point control block in
free assign mode or key/AUX bus delegation mode,
press the [KEY] button on the cross-point pad, turning it
on, and select a key source signal.
• To select a video signal on the cross-point control block
in free assign mode or key/AUX bus delegation mode,
press the [KEY] button on the cross-point pad, turning it
off, and select a key source signal.
Note
When a key source bus delegation button is assigned on the
AUX bus control block (AUX bus operation mode), you
can perform the operation using the [KEY] button on the
cross-point pad.
When a cross-point button on the 3rd/4th row is pressed
while pressing the [KEY] button, the key signal is selected.
When a cross-point button on the 3rd/4th row is pressed
without pressing the [KEY] button, the video signal is
selected.
To select a key source in the menu
1
In the M/E-1 >Key1 >Type menu (1111), press [Key
Bus] in the <Key Fill> group.
2
Press [Signal Select].
The Signal Select menu (1111.3) appears.
3
In the <Target> group, press [Source].
4
In the <Key Source> group, specify the key source
selection mode (Self, Auto Select, or Split).
For details, refer to step 5 in "Selecting the key fill and
key source" (page 111).
5
If [Split] is selected in step 4, select a key source signal
from the list on the right.
6
In the <Assign> group, select the video signal or key
signal from the V/K pair to assign to the key source.
112