Toshiba TOSVERT VF-AS1 Instruction Manual page 245

[23] Acceleration/deceleration 2 [2/2]
Communi
Title cation Function
No.
0514 Acceleration time 4
f514
0515 Deceleration time 4
f515
Acceleration/ deceleration 4
f516 0516
pattern
Acceleration/deceleration
f517 0517
switching frequency 3
*1: Default values vary depending on the capacity. ⇒ See the table of K-46.
*2: Changing the parameter  enables to set to 0.01 sec. (adjustment range: 0.01~600.0 sec.).
[24] Pattern operation [1/3]
Communi
Title cation Function
No.
0520 Pattern operation selection
f520
0521 Pattern operation mode
f521
Number of repetitions of pattern
0522
f522
group 1
f523 0523 Pattern group 1 selection 1
0524 Pattern group 1 selection 2
f524
f525 0525 Pattern group 1 selection 3
f526 0526 Pattern group 1 selection 4
0527 Pattern group 1 selection 5
f527
f528 0528 Pattern group 1 selection 6
f529 0529 Pattern group 1 selection 7
0530 Pattern group 1 selection 8
f530
Number of repetitions of pattern
f531 0531
group 2
0532 Pattern group 2 selection 1
f532
f533 0533 Pattern group 2 selection 2
0534 Pattern group 2 selection 3
f534
0535 Pattern group 2 selection 4
f535
f536 0536 Pattern group 2 selection 5
0537 Pattern group 2 selection 6
f537
0538 Pattern group 2 selection 7
f538
f539 0539 Pattern group 2 selection 8
Adjustment range
0.1~6000 sec.
0.1~6000 sec.
0:Straight, 1:S-pattern 1, 2:S-pattern 2
0.0~ Hz
Adjustment range
0:Deselect
1:Select (setting in units of seconds)
2:Select (setting in units of minutes)
0:Pattern operation reset when system stops
operation
1:Pattern operation continued even after system
stops operation
1~254, 255:∞
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
1~254, 255:∞
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
0:Skip, 1~15
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
0.1/0.1 *2 *1 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
1/1 0 Enabled ●/●
0.01/0.01 0.0 Enabled ●/●
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 1 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 1 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
1/1 0 Disabled ●/●
PM
V/f Constant Reference
Torque
control
control
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
PM
V/f Constant Reference
Torque
control
control
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31
- ● ● 6. 31