Toshiba TOSVERT VF-AS1 Instruction Manual page 243

[21] Torque limit [2/2]
Communi
Title cation Function
No.
Regenerative braking torque
0443
f443
limit 1 level
Power running torque limit 2
0444
f444
level
Regenerative braking torque
f445 0445
limit 2 level
Power running torque limit 3
f446 0446
level
Regenerative braking torque
f447 0447
limit 3 level
Power running torque limit 4
f448 0448
level
Regenerative braking torque
0449
f449
limit 4 level
Acceleration/deceleration
0451
f451
operation after torque limit
Power running stall continuous
0452
f452
trip detection time
Regenerative braking stall
f453 0453
prevention mode selection
[22] Adjustment parameters [1/2]
Communi
Title cation Function
No.
0458 Current control proportional gain 0.0~100.0
f458
0460 Speed loop proportional gain
f460
Speed loop stabilization
f461 0461
coefficient
f462 0462 Moment of inertia of load 1
f463 0463 Second speed loop proportional gain 1~9999
Second speed loop stabilization
0464
f464
coefficient
f465 0465 Moment of inertia of load 2
0466 Speed PI switching frequency
f466
f470 0470 VI/II input bias
f471 0471 VI/II input gain
f472 0472 RR/S4 input bias
0473 RR/S4 input gain
f473
f474 0474 RX input bias
f475 0475 RX input gain
0476 A1 input bias
f476
f477 0477 A1 input gain
*1: ⇒ For details refer to the Instruction Manual (xxxxxxxx) for this parameter.
*2: ⇒ Settings vary from unit to unit. Even if  is set to , no change is made to these values.
Adjustment range
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0.0~249.9%, 250.0%:Disabled
0:In sync with acceleration/deceleration
1:In sync with min. time
0.0~1.0 sec.
0:Stall during regenerative braking
1:Not stall during regenerative braking
Adjustment range
1~9999
1~9999
0~100
1~9999
0~100
0.0~ Hz
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
0.1/0.01 250.0 Enabled ●/●
1/1 0 Disabled ●/●
0.1/0.1 0.0 Enabled ●/●
1/1 0 Enabled ●/●
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
setting running
(Panel/Communi
control
cation)
0.1/0.1 0.0 Enabled ●/●
1/1 40 Enabled ●/●
1/1 100 Enabled ●/●
1/1 35 Enabled ●/●
1/1 40 Enabled ●/●
1/1 100 Enabled ●/●
1/1 35 Enabled ●/●
1/1 0.0 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
1/1 *2 Enabled ●/●
PM
V/f Constant Reference
Torque
control
control
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
●/● ● ● 6. 25. 1
- ● ● 6. 25. 2
- ● ● 6. 26. 1
- ● ● 6. 26. 2
PM
V/f Constant Reference
Torque
control
control
●/● - - *1
- - - *1
- - - *1
- ● - *1
- - - *1
- ● - *1
- ● - *1
- - - *1
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28
●/● ● ● 6. 28