Toshiba TOSVERT VF-AS1 Instruction Manual page 244

[22] Adjustment parameters [2/2]
Communi
Title cation Function
No.
0478 A2 input bias
f478
0479 A2 input gain
f479
PM motor constant 1 (d axis
f498 0498
inductance)
PM motor constant 2 (q axis
f499 0499
inductance)
*1: ⇒ Settings vary from unit to unit. Even if  is set to , no change is made to these values.
[23] Acceleration/deceleration 2 [1/2]
Communi
Title cation Function
No.
0500 Acceleration time 2
f500
f501 0501 Deceleration time 2
Acceleration/deceleration 1
0502
f502
pattern
Acceleration/deceleration 2
0503
f503
pattern
Acceleration/deceleration 1, 2,
f504 0504
3, 4 selection
Acceleration/deceleration
f505 0505
switching frequency 1
Acceleration S-pattern lower
f506 0506
limit adjustment
Acceleration S-pattern upper
f507 0507
limit adjustment
Deceleration S-pattern lower
f508 0508 limit adjustment (accel./decel.
time lower limit erase)
Deceleration S-pattern upper
f509 0509
limit adjustment
0510 Acceleration time 3
f510
f511 0511 Deceleration time 3
Acceleration/ deceleration 3
0512
f512
pattern
Acceleration/deceleration
0513
f513
switching frequency 2
*1: Default values vary depending on the capacity. ⇒ See the table of K-46.
*2: Changing the parameter  enables to set to 0.01 sec. (adjustment range: 0.01~600.0 sec.).
Adjustment range
0~255
0~255
0~100%
0~100%
Adjustment range
0.1~6000 sec.
0.1~6000 sec.
0:Straight, 1:S-pattern 1, 2:S-pattern 2
0:Straight, 1:S-pattern 1, 2:S-pattern 2
1:Acceleration/deceleration 1
2:Acceleration/deceleration 2
3:Acceleration/deceleration 3
4:Acceleration/deceleration 4
0.0~ Hz
0~50%
0~50%
0~50%
0~50%
0.1~6000 sec.
0.1~6000 sec.
0:Straight, 1:S-pattern 1, 2:S-pattern 2
0.0~ Hz
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
1/1 *1 Enabled ●/●
1/1 *1 Enabled ●/●
1/1 40 Disabled -
1/1 40 Disabled -
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
0.1/0.1 *2 *1 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
1/1 １ Enabled ●/●
0.01/0.01 0.0 Enabled ●/●
1/1 10 Enabled ●/●
1/1 10 Enabled ●/●
1/1 10 Enabled ●/●
1/1 10 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
1/1 0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
PM
V/f Constant Reference
Torque
control
control
●/● ● ● 6. 28
●/● ● ● 6. 28
- ● - 6. 29
- ● - 6. 29
PM
Torque V/f Constant Reference
control
control
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1
- ● ● 6. 30. 1