Garmin G1000 Pilot's Manual page 445

Message
NAV1 SERVICE – NAV1 needs service.
Return unit for repair.
NAV2 MANIFEST – NAV2 software
mismatch, communication halted.
NAV2 RMT XFR – NAV2 remote
transfer key is stuck.
NAV2 SERVICE – NAV2 needs service.
Return unit for repair.
NON WGS84 WPT – Do not use GPS
for navigation to [xxxx]
PFD1 BACKLIGHT CALIBRATION –
PFD1 bklt cal lost or mismatch. Return
for repair.
PFD1 CARD 1 ERR – PFD1 card 1 is
invalid.
PFD1 CARD 1 REM – PFD1 card 1 was
removed. Reinsert card.
PFD1 CARD 2 ERR – PFD1 card 2 is
invalid.
PFD1 CARD 2 REM – PFD1 card 2 was
removed. Reinsert card.
PFD1 CONFIG – PFD1 config error.
Config service req'd.
PFD1 COOLING – PFD1 has poor
cooling. Reducing power usage.
PFD1 DB ERR – PFD1 basemap
database is incompatible.
PFD1 DB ERR – PFD1 database error
exists.
PFD1 DB ERR – PFD1 Obstacle
database missing.
PFD1 DB ERR – PFD1 Terrain database
missing.
PFD1 KEYSTK – PFD1 [key name] Key
is stuck.
PFD1 MANIFEST – PFD1 software
mismatch, communication halted.
190-02692-00 Rev. A
Comments
A failure has been detected in the NAV1 receiver. The receiver may still be available.
The G1000 system should be serviced.
NAV2 software mismatch. The system should be serviced.
The remote NAV2 transfer switch is stuck in the enabled (or "pressed") state. Press
the transfer switch again to cycle its operation. If the problem persists, the G1000
system should be serviced.
A failure has been detected in the NAV2 receiver. The receiver may still be available.
The G1000 system should be serviced.
The position of the selected waypoint [xxxx] is not calculated based on the WGS84
map reference datum and may be positioned in error as displayed. Do not use GPS to
navigate to the selected non-WGS84 waypoint.
The specified GDU's backlight calibration cannot be found or found or is invalid. The
system should be serviced.
The SD card in the top card slot of the specified PFD or MFD contains invalid data.
The SD card was removed from the top card slot of the specified PFD or MFD. The SD
card needs to be reinserted.
The SD card in the bottom card slot of the specified PFD or MFD contains invalid data.
The SD card was removed from the bottom card slot of the specified PFD or MFD. The
SD card needs to be reinserted.
The PFD configuration settings do not match backup configuration memory. The
G1000 system should be serviced.
The PFD is overheating and is reducing power consumption by dimming the display.
If problem persists, the G1000 system should be serviced.
PFD1 detected an incompatibility in the basemap database.
PFD1 detected a failure in one or more databases. If problem persists, the system
should be serviced.
The obstacle database is present on another LRU, but is missing on the specified LRU.
Ensure the data card is properly inserted. Replace data card. If problem persists, the
G1000 system should be serviced.
The terrain database is present on another LRU, but is missing on the specified LRU.
Ensure the data card is properly inserted. Replace data card. If problem persists, the
G1000 system should be serviced.
A key is stuck on the PFD bezel. Attempt to free the stuck key by pressing it several
times. The G1000 system should be serviced if the problem persists.
The PFD has incorrect software installed. The G1000 system should be serviced.
Garmin G1000 Pilot's Guide for the Piper PA-32 Saratoga
APPENDIX A
425