Garmin G1000 Cockpit Reference Manual
  1. Manuals
  2. Brands
  3. Garmin Manuals
  4. Avionics Display
  5. Cessna Caravan G1000
  6. Cockpit reference manual

Garmin G1000 Cockpit Reference Manual

Integrated avionics system diamond da62
Hide thumbs Also See for G1000:
Table of Contents

Advertisement

Quick Links

Download this manual
G1000
®
Integrated Avionics System
Cockpit Reference Guide for the Diamond DA62

Advertisement

Table of Contents
loading

Related Manuals for Garmin G1000

Summary of Contents for Garmin G1000

  • Page 1 G1000 ® Integrated Avionics System Cockpit Reference Guide for the Diamond DA62...
  • Page 3 FLIGHT INSTRUMENTS ENGINE INDICATION SYSTEM NAV/COM/TRANSPONDER/AUDIO PANEL AUTOMATIC FLIGHT CONTROL SYSTEM GPS NAVIGATION FLIGHT PLANNING PROCEDURES HAZARD AVOIDANCE ADDITIONAL FEATURES ABNORMAL OPERATION ANNUNCIATIONS & ALERTS APPENDIX INDEX...
  • Page 5 , Garmin SVT , and Connext are trademarks ™ ™ ™ of Garmin International, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Skywatch and Stormscope are registered trademarks of L-3 Communications. Ryan , TCAD ®...
  • Page 6 Garmin’s use of the information in the datasets. Some jurisdictions do not allow the limitation or exclusion of implied warranties or liability for incidental or consequential damages so the above limitations or exclusions may not apply to licensee.
  • Page 7 Warnings, Cautions & Notes WARNING: Do not use terrain avoidance displays as the sole source of infor- mation for maintaining separation from terrain and obstacles. Garmin obtains terrain and obstacle data from third party sources and cannot independently verify the accuracy of the information.
  • Page 8 WARNING: When using the autopilot to fly an approach with vertical guid- ance, the autopilot will not level the aircraft at the MDA/DH even if the MDA/ DH is set in the altitude preselect. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 9 WARNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. Garmin SVT is intended as an aid to situ- ational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic.
  • Page 10 Warnings, Cautions & Notes CAUTION: Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and affect the airworthiness of the aircraft. NOTE: Lamp(s) inside this product contain mercury (HG) and must be recycled or disposed of according to local, state, or federal laws.
  • Page 11 ‘Type 2 LOA Status.’ • Use of a current Garmin or Jeppesen database in your Garmin equipment is required for compliance with established FAA regulatory guidance, but does not constitute authorization to fly any and all terminal procedures that may be presented by the system.
  • Page 12 If the secondary source is a Portable Electronic Device (PED), its use must be consistent with guidance in AC 120-76C. NOTE: Operate G1000 system power through at least one cycle in a period of four days of continuous operation to avoid an autonomous system reboot.
  • Page 13 It is not intended to be a comprehensive operating guide. Complete operating procedures for the system are found in the Pilot’s Guide for this aircraft. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 14 Warnings, Cautions & Notes Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 15 Added Bluetooth Management for Flight Stream 210 Updated CAS Messages Updated Weather and Traffic Messages Updated System Messages Updated Softkey Maps Revision Date of Revision Affected Pages Description September, 2016 Production release RR-1 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 16 Record of Revisions Blank Page RR-2 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 17: Table Of Contents

    GPS Navigation ........................... 17 Direct-to Navigation ......................17 Activate a Stored Flight Plan ....................18 Activate a Flight Plan Leg ..................... 18 Stop Navigating a Flight Plan ....................19 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 18 Onboard Lightning Detection System (Optional) ............43 SiriusXM Weather (Optional) ....................45 Garmin Connext Weather (Optional) .................. 47 FIS-B Weather .......................... 59 Airborne Color Weather Radar .................... 66 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 19 Weather Radar Alerts and Annunciations ............... 117 GDL 69A SXM Data Link Receiver Messages ..............118 ADS-B Status Page messages ..................... 119 G1000 System Message Advisories ................... 120 Flight Plan Import/Export Messages ................138 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 20 Table of Contents Appendix ............................141 PFD Softkey Map ........................141 MFD Softkey Map ......................... 146 Loading Updated Databases ....................148 Index ............................Index-1 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 21: Flight Instruments

    2) Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2 or LOC2. This places the light blue tuning box over the NAV2 standby frequency. 3) Press the CDI Softkey a third time to return to GPS. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 22: Enable/Disable Obs Mode While Navigating With Gps

    4) Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF field. 5) Turn the small FMS Knob clockwise to ON or counterclockwise to OFF. 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 23: Set Barometric/Radar Altimeter Minimum Descent Altitude

    1) Press the PFD Softkey. 2) Press the DME Softkey to display the DME Information Window. 3) To remove the DME Information Window, press the DME Softkey again. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 24: Selecting Bearing Display And Changing Sources

    4) Press the BRG1 Softkey or BRG2 Softkey again to change the bearing source to ADF. 5) To remove the bearing pointer and information window, press the BRG Softkey again. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 25: Engine Indication System

    NOTE: Refer to the Airplane Flight Manual (AFM) for applicable RPM indications. ENGINE DISPLAY Engine Load Indicator Tachometer Fuel Flow Indicator Oil Temperature Indicator Oil Pressure Indicator Coolant Temperature Indicator Fuel Temperature Indicator Fuel Quantity Indicator Engine Display 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 26: System Display

    Oil Pressure Indicator Deice Fluid Indicator System Display FUEL DISPLAY Pressing the ENGINE Softkey displays the SYSTEM and FUEL softkeys. Press the FUEL Softkey to show the Fuel Display. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 27 Indicator Tachometer Fuel Quantity Indicator Fuel Flow Indicator Fuel Temperature Indicator Gallons Remaining Fuel Used Endurance Fuel Range in Nautical Miles Total Time In Service Indicator Fuel Display 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 28 From the Fuel Display, press the RST FUEL Softkey. This resets the displayed fuel remaining (GAL REM) to 50 gallons (or 86 gallons if optional aux fuel tanks are installed). The fuel used (GAL USED) is reset to zero. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 29: Nav/Com/Transponder/Audio Panel

    2) Turn the large FMS to select the DME source field. 3) Turn the small FMS Knob to select the desired Nav radio. 4) Press the ENT Key to complete the selection. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 30: Enter A Transponder Code

    The large knob enters MHz and the small knob enters kHz. 3) Press the Frequency Transfer Key to place the frequency into the active frequency field. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 31: Digital Clearance Recorder And Player

    Selected Selected radios; pilot; radios; pilot; COPILOT Copilot passengers; passengers; music music Selected Selected Passengers; CREW radios; pilot; radios; pilot; music copilot copilot 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 32 Nav/Com/XPDR/Audio Panel Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 33: Garmin Automatic Flight Control System

    *Valid VNV flight plan must be entered before VNV Key press activates flight director. **The selected navigation receiver must have a valid VOR or LOC signal or active GPS course before NAV or APR Key press activates flight director. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 34: Vertical Modes

    ** ALTV is armed automatically under VPTH when the VNV Target Altitude is to be captured instead of the Selected Altitude. ***GP is available in installations with GIA 63W IAUs when SBAS is available. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 35: Lateral Modes

    Go Around angle and wings level Button The Garmin AFCS limits turn rate to 3 degrees per second (standard rate turn). UNDERSPEED PROTECTION Underspeed Protection is available when the optional Electronic Stability and Protection (Garmin ESP) system is installed and the autopilot is on.
  • Page 36 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 37: Gps Navigation

    ENT Key to activate. To enter an altitude constraint, proceed to step 6. 6) Turn the large FMS Knob to place the cursor over the ‘ALT’ altitude field. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 38: Activate A Stored Flight Plan

    Press the MENU Key, select the ‘Activate Leg’ option from the page menu and press the ENT Key. This step must be used when activating a leg from the PFD. 3) With ‘Activate’ highlighted, press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 39: Stop Navigating A Flight Plan

    Small Light Blue Subdued Text Small White Text with Altitude Restriction Bar Cross AT or ABOVE 5,000 ft Cross AT 2,300 ft Cross AT or BELOW 3,000 ft 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 40 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 41: Flight Planning

    Turn the small FMS Knob to select the desired flight plan (already stored in memory), by number. c) Turn the large FMS Knob to highlight the ‘LEG’ field. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 42 Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, the baro setting is provided by the setting entered on the PFD. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 43: Create A User Waypoint Defined By Latitude & Longitude

    2) Turn the small FMS Knob to select the User WPT Information Page. 3) Press the NEW Softkey. A waypoint is created at the current aircraft position. 4) Enter the desired waypoint name. 5) Press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 44 Turn the small FMS Knob to the right to display the ‘RECENT’ waypoints. c) Turn the large FMS Knob to select the desired waypoint. d) Press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 45: Create A User Waypoint Defined By A Radial & Distance From Another Waypoint

    7) With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to display a list of waypoint types. 8) Turn the small FMS Knob to select RAD/DIS (radial/distance). 9) Press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 46 12) Press the ENT Key. 13) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired distance from the reference waypoint. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 47: Delete A User Waypoint

    5) Repeat step numbers 3 and 4 to enter each additional flight plan waypoint. 6) When all waypoints have been entered, press the FMS Knob to remove the cursor. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 48: Import A Flight Plan From An Sd Card

    5) Turn either FMS Knob to highlight an empty or existing flight plan. 6) Press the IMPORT Softkey. If an empty flight plan is selected, a list of the available flight plans on the SD card will be displayed. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 49: Insert A Waypoint In The Active Flight Plan

    Turn the small FMS Knob to the right to display the ‘RECENT’ waypoints. c) Turn the large FMS Knob to select the desired waypoint. d) Press the ENT Key. e) Press the ENT Key again to accept the waypoint. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 50: Enter An Airway In A Flight Plan

    5) Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course direction, and press the ENT Key. 6) Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 51 5) Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course direction, and press the ENT Key. 6) Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 52: Invert An Active Flight Plan

    4) Press the ENT Key. The original flight plan remains intact in its flight plan catalog storage location. 5) With ‘OK’ highlighted, press the ENT Key to invert the flight plan. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 53: Remove A Departure, Arrival, Approach, Or Airway From A Flight Plan

    5) Turn the large FMS Knob to place the cursor in the desired location. 6) Enter the changes, then press the ENT Key. 7) Press the FMS Knob to return to the Flight Plan Catalog Page. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 54: Delete A Waypoint From The Flight Plan

    2) Turn the small FMS Knob to select the Flight Plan Catalog Page. 3) Press the FMS Knob to activate the cursor. 4) Turn the large FMS Knob to highlight the flight plan to be copied. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 55: Delete A Flight Plan

    The default user waypoint naming is USR000, USR001, USR002, and so on. 5) To change the user waypoint name, follow the procedure for modifying a user waypoint. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 56: Export A Flight Plan To An Sd Card

    5) Turn the large FMS Knob to highlight the flight plan to be exported. 6) Press the EXPORT Softkey. 7) Press the ENT Key to confirm the export. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 57: Procedures

    2) Turn the large FMS Knob to highlight ‘SELECT ARRIVAL’. 3) Press the ENT Key. The cursor is displayed in the ‘ARRIVAL’ field with a list of available arrivals. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 58: Activate An Arrival Leg

    1) Press the PROC Key. 2) Turn the large FMS Knob to highlight ‘SELECT APPROACH’. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 59 Selecting ‘ACTIVATE?’ enters the selected approach procedure into the active flight plan and activates the first leg of the approach. 13) Press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 60: Activate An Approach In The Active Flight Plan

    When temperature compensated altitude is enabled for the loaded approach, the altitudes associated with the approach waypoints are displayed in slanted text. Altitudes Displayed Without Altitudes Displayed With Temperature Compensation Temperature Compensation Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 61 3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is displayed. 4) Press the ENT Key. ‘CANCEL COMPENSATION?’ is highlighted. The temperature compensated altitude at the FAF 5) Press the ENT Key. is cancelled. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 62 Procedures Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 63: Hazard Avoidance

    WARNING: The lightning detection system system is not intended to be used for hazardous thunderstorm penetration. Weather information on the G1000 MFD is approved for weather avoidance only. Refer to the lightning detection system pilot’s guide for detailed operation. Displaying Lightning Data on the Navigation Map Page 1) Press the MAP Softkey.
  • Page 64 360 Softkey to display a 360˚ viewing area or press the ARC Softkey to display a 120˚ viewing area. Press the CLEAR Softkey to remove all lightning data from the display. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 65: Siriusxm Weather (Optional)

    ENT Key and select that Airport’s Information Page to display the text of the report. Pressing the ENT Key when panning over a TFR displays TFR specific information. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 66 Cell Movement (CELL MOV) SIGMETs/AIRMETs (SIG/AIR) Meteorological Aerodrome Report (METARs) City Forecast (CITY) Surface Analysis (SFC) Freezing Levels (FRZ LVL) Winds Aloft (WIND) County Warnings (COUNTY) Cyclone Warnings (CYCLONE) Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 67: Garmin Connext Weather (Optional)

    States or (011) 913-440-1135. After a subscriber account has been established, the system must be registered for data link features such as reporting services or Connext Worldwide Weather. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 68 Window is now displayed. 7) Press the MENU Key. The Page Menu window is now displayed. 8) Using the FMS Knob enter the access code obtained from Garmin Flight Data Services in the ACCESS CODE field. 9) Press the ENT Key. REGISTER will now be highlighted.
  • Page 69 Canadian radar precipitation data provided by Environment Canada. ˆ Australian radar precipitation data provided by the Australian Bureau of Meteorology. Garmin Connext Weather Product Symbols and Data Timing 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 70 3) Press the MENU Key. 4) Turn the large FMS Knob to select ‘Display Connext Weather’, or ‘Display XM Weather’ (choice dependent on current weather source) and press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 71 (if desired), and the ability to send or cancel weather data requests. The window also displays the status of the Connext data request process. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 72 Connext Data Request, regardless of which products (if any) are currently enabled for display. On subsequent requests, previously retrieved textual data (such as METARs and TAFs) is retained if it has not expired, while new textual weather data matching the current coverage area and all graphical weather data Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 73 30 minutes. Connext Server Inop The Connext weather data server will be out of service for at least 30 minutes. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 74 Enabling Automatic Connext Data Requests 1) Select the Connext Weather Data Link Page. 2) Press the MENU Key. 3) With ‘Connext Weather Request’ highlighted, press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 75 All weather product legends can be viewed on the Connext Weather Data Link Page. For the Precipitation legend, press the LEGEND Softkey when Precipitation is selected for display. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 76 Neither cloud-to-cloud nor the exact location of the lightning strike is displayed. If the aircraft is also equipped with an on-board lightning detection system, only one lightning product may be enabled for display at a time. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 77 4) Use the FMS Knob or the ENT Key to scroll through the METAR and TAF text. METAR text must be completely scrolled through before scrolling through the TAF text. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 78 A PIREP may contain unforecast adverse weather conditions, such as low in-flight visibility, icing conditions, wind shear, turbulence, and type of aircraft flown. PIREPs are issued as either Routine (UA) or Urgent (UUA). Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 79: Fis-B Weather

    The optional GDL 88 receives Flight Information Services - Broadcast (FIS-B) weather data from a network of UAT ground-based transceivers (GBTs). FIS-B weather data reception requires the aircraft being within range and line-of- sight of an operating GBT broadcasting FIS-B weather data. Reception may be affected by factors including altitude or terrain. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 80 FIS-B Weather’, and press the ENT Key. Expiration Time Broadcast Rate FIS-B Weather Product Symbol (Minutes) (Minutes) NEXRAD Composite (US) NEXRAD Composite (Regional) Meteorological Aerodrome Report (METARs) Pilot Weather Report (PIREPs) Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 81 Setting Up and Customizing FIS-B Weather on the Navigation Map Page 1) Select the Navigation Map Page. 2) Press the MENU Key. 3) With ‘Map Setup’ highlighted, press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 82 1) Select the Navigation Map Page. 2) Press the MAP Softkey. 3) Press the LEGEND Softkey (available if one or more FIS-B weather products are enabled for display). Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 83 METAR text must be completely scrolled through before scrolling through the TAF text. 5) Press the FMS Knob or the CLR Key to return to the Weather Data Link (FIS-B) Page. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 84 5) Turn the small FMS Knob to highlight the Temp (•) ‘ON’ or ‘OFF’ field, then press the ENT Key. 6) When finished, push the FMS Knob or the CLR Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 85 4) If necessary, turn the FMS Knob to select ‘Review Airspaces’ and press the ENT Key. The system displays the INFORMATION window. 5) Press the FMS Knob or the CLR Key to remove the INFORMATION window. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 86: Airborne Color Weather Radar

    Standby Mode before taxiing the aircraft to prevent the antenna from bouncing on the bottom stop and possibly causing damage to the radar assembly. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 87 Red (GWX 70) 41 dBz and greater 0.5 and greater Magenta* (GWX 68 only) 50 dBZ and greater > 2 *Magenta color not applicable to GWX 70 installations 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 88 Remember to return the gain setting to ‘Calibrated’ for viewing the actual intensity of precipitation. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 89 18 dB to < 27 dB Magenta (GWX 70) 21 dB < 29 dB Blue (GWX 68) 27 dB and greater Blue (GWX 70) 29 gB and greater 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 90: Traffic Systems

    Standby Mode. TRAFFIC SYSTEMS • If Traffic information Service (TIS) is configured, STANDBY, OPERATE, and TNA MUTE softkeys are displayed. • If a Traffic Advisory System (TAS) is configured, MUTE and ALT MODE softkeys are displayed. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 91 Traffic Advisory Off Scale Traffic Symbol Description Traffic Information Service (TIS) NOTE: If the G1000 is configured to use an optional Traffic Advisory System (TAS), TIS is not available for use. NOTE: Traffic Information Service (TIS) is only available when the aircraft is within the service volume of a TIS capable terminal radar site.

  • Page 92: Gdl 88 Ads-B Traffic (Optional)

    2) If necessary, turn the Joystick to select a map range of 2 and 6 nm to ensure full test pattern display. 2) Ensure the ADS-B Softkey is disabled. 3) If the optional TAS/TCAS I is installed, ensure the TAS STBY Softkey is enabled. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 93 1) Select the Traffic Map Page. 2) Press the MOTION Softkey. 3) Press the DURATION Softkey. 4) Press a softkey for the desired duration (30 SEC, 1 MIN, 2 MIN, 5 MIN). 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 94 NOT CONFIGURED Traffic application is not available, because it has not been configured. If this annunciation persists, the system should be serviced. ---------------- Traffic application status is invalid or unknown. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 95 If no uplink has been received, or the status is invalid, dashes appear instead of a number of minutes. AUX-ADS-B Status Page Messages for ADS-B Traffic 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 96: Terrain And Obstacle Proximity

    NOTE: Terrain-SVS is only available when Synthetic Vision Technology (SVT) option is installed. NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75 degrees north or 60 degrees south. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 97 1) While the Terrain-SVS Page is displayed, press the MENU Key. 2) Turn the small FMS Knob to select “Show (or Hide) Aviation Data”. 3) Press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 98 While the Terrain-SVS Page is displayed, press the INHIBIT Softkey. 1) While the Terrain-SVS Page is displayed, press the MENU Key. 2) Turn the small FMS Knob to select ‘Enable Terrain’. 3) Press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 99: Additional Features

    1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. 3) Press the SYN TERR Softkey. The SVT display will cycle on or off with the SYN TERR Softkey. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 100: Terminal Procedure Charts

    DCLTR Softkey a third time removes the airport runway layout, unless the airport in view is part of an active route structure. Pressing the DCLTR Softkey again cycles back to the original map detail. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 101 3) Press the GO BACK Softkey to return to the previous page. View Charts from the Active Flight Plan Page 1) While viewing the Active Flight Plan Page, press the FMS Knob to activate the cursor. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 102: Airport Directory

    Directory information is displayed on the right half of the display. SIRIUSXM SATELLITE RADIO ENTERTAINMENT (OPTIONAL) The XM ® Radio Page provides information and control of the audio entertainment features of the SiriusXM Satellite Radio. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 103 Knob to scroll through the channels. 3) With the desired channel highlighted, press the ENT Key. Entering a Channel Directly 1) While on the XM Radio Page, press the CHNL Softkey. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 104: Satellite Telephone & Sms Messaging Service (Optional)

    NOTE: Aural and pop-up visual annunciations for incoming calls and received text messages are inhibited during taxiing, takeoff and landing roll, low altitude operations, low airspeed operations, and excessive pitch and roll attitudes. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 105 A subscriber account must be established prior to using the Iridium Satellite System. Before setting up an Iridium account, obtain the serial number of the Iridium Transceiver and the System ID by viewing the AUX- SYSTEM STATUS Page. Contact Garmin Connext at 1-866-739-5687 in the United States or 913-397-8200, ext. 1135. Disable/Enable Iridium Transceiver Iridium telephone may be turned on or off by performing the following steps.
  • Page 106 Phone is dialing another phone Phone has failed Phone status not known Phone is disabled Phone is reserved for data transmission Calling other phone or incoming call from other phone Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 107 Selecting the TEL Softkey will display the AUX-TELEPHONE Page allowing additional call information to be viewed before answering. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 108 8816 or 8817 Globalstar 8818 or 8819 6) Press the ENT Key. ‘OK’ is highlighted. 7) Press the ENT Key. The system will begin calling the number. To exit the call, press the HANGUP Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 109 Text message has been sent System failed to send text message Predefined text message Viewing a Text Message When Received When viewing MFD pages other than the AUX-TEXT MESSAGING Page, a pop-up alert will be displayed when a new text message is received. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 110 MFD by pressing the NUMBERS Softkey. Press the CAP LOCK Softkey to create upper and lower case alpha characters. Special characters can be accessed by pressing the SYMBOLS Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 111 6) Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field. 7) Enter the desired message using any combination of entry methods as described in step 5. 8) Press the ENT Key. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 112 Drafts. Each text message box may be viewed separately, or together in any combination. Show Inbox Messages While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 113 (read, unread, sent, unsent, etc.), or by message address. View Messages Sorted by Message Date/Time: While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE Softkey, then press the TIME Softkey. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 114 Press the MENU Key to display the Page Menu. b) Turn either FMS Knob to place the cursor on ‘View Selected Message’. c) Press the ENT Key. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 115 1) While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the FMS Knob to activate the cursor. 2) Turn either FMS Knob to select the desired message. 3) Press the DELETE Softkey. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 116: Electronic Stability And Protection (Garmin Esp ) (Optional)

    Press the ENT Key. ELECTRONIC STABILITY AND PROTECTION (GARMIN ESP ) (OPTIONAL) ™ NOTE: Refer to the Airplane Flight Manual to determine approval of Garmin ESP functionality. The pilot can interrupt ESP by pressing and holding the Autopilot Disconnect (AP DISC) switch. Upon releasing the or AP DISC switch, ESP force will again be applied, provided aircraft roll attitude is within engagement limits.

  • Page 117: Auxiliary Video (Optional)

    2) Turn the small FMS Knob to select VIDEO and display the AUX-VIDEO Page. The video display softkeys shown below appear on the AUX - VIDEO Page. Control of the AUX - VIDEO Page can also be accessed through the Page Menu. Selecting video menu options: 1) While viewing the AUX - VIDEO Page press the MENU Key to display the Page Menu OPTIONS. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 118 The RANGE Knob can be used to increase or decrease the range setting on the map display or zoom in and out on the video display. While in the Split-Screen Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 119: Electronic Checklists (Optional)

    ‘GO TO NEXT CHECKLIST?’ is highlighted. If ‘GO TO NEXT CHECKLIST?’ is selected prior to checking all the checklist items, ‘*CHECKLIST NOT FINISHED*’ will be displayed in yellow text. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 120 7) Select the RETURN Softkey to return to the previous checklist. 8) Select the EXIT Softkey to exit the Checklist Page and return to the page last viewed. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 121: Bluetooth ® Management

    Stream device for a Bluetooth connection between the G1000 and a mobile device ™ running the Garmin Pilot application. The mobile device must be ‘paired’ with the G1000 in order to use the various functions. Pairing is accomplished by first placing the G1000 in pairing mode by displaying the Bluetooth Management Page. The G1000 is ‘discoverable’ whenever this page is displayed. The pairing operation is completed from the mobile device and the Garmin Pilot application. See the device Bluetooth pairing instructions and the connection instructions in the Garmin Pilot application.
  • Page 122 2) Turn the large FMS Knob to highlight the desired paired device. 3) Turn the small FMS Knob to select ‘ENABLED’ or ‘DISABLED’. Selecting ‘ENABLED’ allows the G1000 to automatically connect to a previously paired device when detected. 4) Press the FMS Knob to remove the cursor.

  • Page 123: Abnormal Operation

    Abnormal Operation ABNORMAL OPERATION REVERSIONARY MODE Should a system detected failure occur in either display, the G1000 automatically enters reversionary mode. In reversionary mode, critical flight instrumentation is combined with engine instrumentation on the remaining display. Reversionary display mode can be manually activated by pressing the DISPLAY BACKUP Button on the audio panel.

  • Page 124: Unusual Attitudes

    While in Enroute or Oceanic phase of flight, if the G1000 detects an invalid GPS solution or is unable to calculate a GPS position, the system automatically reverts to Dead Reckoning (DR) Mode. In DR Mode, the G1000 uses its last-known position combined with continuously updated airspeed and heading data (when available) to calculate and display the aircraft’ s current estimated position.
  • Page 125 “NO GPS POSITION” annunciation on the map and the G1000 stops navigating in GPS Mode. DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’ superimposed in yellow over the ‘own aircraft’ symbol as shown in the following figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly...
  • Page 126 • All Bearing Pointer Distances • Active Flight Plan distances, bearings, and ETE values Also, while the G1000 is in DR Mode, the autopilot will not couple to GPS, and Terrain Proximity is disabled. Additionally, the accuracy of all nearest information (airports, airspaces, and waypoints) is questionable. Finally, airspace alerts continue to function, but with degraded accuracy.

  • Page 127: Annunciations & Alerts

    Right engine oil pressure is less than 0.9 bar. L STARTER Left engine starter is engaged. R STARTER Right engine starter is engaged. USP ACTIVE USP has engaged autopilot due to slow airspeed. Optional (Garmin ESP only) ™ 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 128: Caution Alerts

    Stall warning heat is off. L VOLTS LOW Left bus voltage is less than 25 volts. R VOLTS LOW Right bus voltage is less than 25 volts. * Optional Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 129: Annunciation Advisory

    Rudder Mistrim Right Yaw servo providing sustained force in the indicated direction Rudder Mistrim Left Aileron Mistrim Right Roll servo providing sustained force in indicated direction Aileron Mistrim Left 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 130: Terrain-Svs Alerts

    TERRAIN-SVS ALERTS PFD/MFD Terrain-SVS Aural Alert Type Page Pop-Up Alert Message Annunciation Reduced Required Terrain “Warning; Terrain, Clearance Warning (RTC) Terrain” Imminent Terrain Impact “Warning; Terrain, Warning (ITI) Terrain” Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 131: Svs Terrain Status Annunciations

    “Terrain System Not Available” GPS signal System Test in progress None System Test pass None “Terrain System Test OK” GPS signal is re- None “Terrain System Available” established 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 132: Voice Alerts

    FAILED The transponder has failed* UNAVAILABLE TIS is unavailable or out of range * Contact a service center or Garmin dealer for corrective action TIS Failure Annunciations Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 133 Traffic is removed because it is too old for coasting (12 to 60 seconds since last message) TRFC RMVD Traffic may exist within the selected display range, but it is not displayed 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 134: Tas Alerts And Annunciations

    Data is being received from the TAS unit, but the unit DATA FAILED is self-reporting a failure FAILED Incorrect data format received from the TAS unit TAS Failure Annunciations Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 135: Ads-B Alerts And Annunciations

    Surface Mode ADS-B: OFF ADS-B TRFC OFF ABD-B Traffic Off ADS-B Traffic Not ADS-B: N/A ADS-B TRFC N/A Available ADS-B Failed* ADS-B: FAIL ADS-B TRFC FAIL Traffic Modes 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 136 NO TRFC DATA Data is not being received from the traffic unit *Shown as symbol on Traffic Map Page **Shown in center of Traffic Map Page Traffic Status Annunciations Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 137: Weather Radar Alerts And Annunciations

    Antenna stabilization is selected off. The radar is not receiving pitch and roll STAB INOP information. The antenna stabilization feature is inoperative. Radar Feature Annunciations on the Weather Radar Page 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 138: Gdl 69A Sxm Data Link Receiver Messages

    Link Receiver within last 5 LINK FAILURE of page minutes ACTIVATION Weather Datalink Page - center SiriusXM subscription is not REQUIRED of page activated GDL 69A SXM Data Link Receiver Messages Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 139: Ads-B Status Page Messages

    Source GPS position source. External #2 The GDL 88 is using the #2 GPS receiver for the GPS position source. --------- The GPS source is invalid or unknown. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 140: G1000 System Message Advisories

    GDC1 is reporting that the altitude error correction error correction is unavailable. is unavailable. ADC1 AS EC – ADC1 airspeed GDC1 is reporting that the airspeed error correction error correction is unavailable. is unavailable. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 141 AHRS1 GPS – AHRS1 using The #1 AHRS is using the backup GPS path. Primary backup GPS source. GPS path has failed. The G1000 system should be serviced when possible. AHRS1 GPS – AHRS1 not The #1 AHRS is not receiving any or any useful GPS receiving any GPS information.
  • Page 142 (or “pressed”) position. Press the PTT switch again to cycle its operation. If the problem persists, the G1000 system should be serviced. COM1 RMT XFR – COM1 The COM1 transfer switch is stuck in the enabled (or remote transfer key is stuck.
  • Page 143 (or “pressed”) position. Press the PTT switch again to cycle its operation. If the problem persists, the G1000 system should be serviced. COM2 RMT XFR – COM2 The COM2 transfer switch is stuck in the enabled (or remote transfer key is stuck.
  • Page 144 DME receiver. Check position sensors. position sensors. FAILED PATH – A data path A data path connected to the GDU or the GIA 63W has failed. has failed. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 145 A failure has been detected in glideslope receiver service. Return unit for repair. 1. The receiver may still be available. The G1000 system should be serviced when possible. G/S2 FAIL – G/S2 is inoperative. A failure has been detected in glideslope receiver 2.
  • Page 146 GDL88 ADS-B NO TX - GDL88 Unable to transmit GDL 88 messages. Failure GDL88 ADS-B TRFC - GDL 88 The GDL 88 is incapable of processing traffic ADS-B traffic has failed information. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 147 North/South, no magnetic approved AHRS operation. Heading is flagged as compass. invalid. GFC MANIFEST – GFC software Incorrect servo software is installed, or gain settings mismatch, communication are incorrect. halted. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 148 Allow units to warm up to operating temperature. GIA2 MANIFEST – GIA2 The GIA 2 has incorrect software installed. The software mismatch, G1000 system should be serviced. communication halted. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 149 The system has detected an over temperature temperature. condition in GRA1. GPS NAV LOST – Loss of GPS navigation. Insufficient Loss of GPS navigation due to insufficient satellites. satellites. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 150 A fault has occurred in the #1 GMU 44. Heading is magnetometer fault has flagged as invalid. The AHRS uses GPS for backup occurred. mode operation. The G1000 system should be serviced. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 151 MFD1 CONFIG – MFD1 config The MFD configuration settings do not match error. Config service req’d. backup configuration memory. The G1000 system should be serviced. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 152 G1000 system should be serviced. MFD1 DB ERR – MFD1 The obstacle database is present on another LRU, obstacle database missing. but is missing on the specified LRU. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 153 The G1000 system should be serviced if the problem persists. MFD1 VOLTAGE – MFD1 has The MFD voltage is low. The G1000 system should low voltage. Reducing power be serviced. usage NAV1 RMT XFR – NAV1 The remote NAV1 transfer switch is stuck in the remote transfer key is stuck.
  • Page 154 The PFD detected a failure in the terrain database. database error exists. Ensure that the terrain card is properly inserted in display. Replace terrain card. If problem persists, the G1000 system should be serviced. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 155 PFD1 KEYSTK – PFD1 [key A key is stuck on the PFD bezel. Attempt to free the name] is stuck. stuck key by pressing it several times. The G1000 system should be serviced if the problem persists. [PFD1 or MFD1] CARD 1 The SD card was removed from the top card slot of REM –...
  • Page 156 The G1000 system should be serviced. Xtalk is off. TIMER EXPIRD – Timer has The system notifies the pilot that the timer has expired. expired. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 157 Annunciations & Alerts Message Advisory Comments TRAFFIC FAIL – Traffic device The G1000 is no longer receiving data from the has failed. traffic system. The traffic device should be serviced. UNABLE V WPT – Can’t reach The current vertical waypoint can not be reached current vertical waypoint.

  • Page 158: Flight Plan Import/Export Messages

    ‘File contained user waypoints only.’ The file stored on the SD card did not contain a flight plan, only user waypoints. One or more of these waypoints did not import successfully. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 159 The stored flight plan was not successfully exported to the SD card. The SD card may not have sufficient available memory or the card may have been removed prematurely. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 160 Annunciations & Alerts Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...

  • Page 161: Appendix

    DCLTR (3) Selects desired amount of map detail; cycles through declutter levels: DCLTR (No Declutter): All map features visible DCLTR-1: Declutters land data DCLTR-2: Declutters land and SUA data DCLTR-3: Removes everything except the active flight plan WX LGND Displays icon and age on the Inset Map for the selected weather products (optional) 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 162 Displays Worldwide Weather precipitation on the Inset Map (optional) XM LTNG Displays XM lightning information on the Inset Map (optional) Displays Worldwide Weather lightning information DL LTNG on the Inset Map (optional) METAR Displays METAR flags on airport symbols shown on the Inset Map (optional) Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 163 Zero-Pitch line APTSIGNS Displays position markers for airports within approximately 15 nm of the current aircraft position. Airport identifiers are displayed when the airport is within approximately 9 nm. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 164 Displays softkeys for setting the altimeter and BARO settings to metric units METERS When enabled, displays altimeter in meters Press to display the BARO setting as inches of mercury Press to display the BARO setting as hectopacals STD BARO Sets barometric pressure to 29.92 in Hg (1013 hPa) Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 165 Automatically enters the VFR code (1200 in the U.S.A. only) Displays transponder code selection CODE softkeys 0-7 0 — 7 Use numbers to enter code 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 166: Mfd Softkey Map

    The CHECK Softkey changes to UNCHECK when the checklist item is already checked CHECK RETURN EXIT EMERGCY MFD Softkeys ENGINE Displays EIS-Engine Page SYSTEM Displays the Engine System Display Displays the fuel softkeys FUEL Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 167 Navigation Map (optional) NEXRAD Displays NEXRAD weather and coverage information on the Navigation Map (optional) PRECIP Displays Worldwide Weather precipita- tion on the Navigation Map (optional) 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 168: Loading Updated Databases

    NOTE: When loading database updates, the ‘DB Mismatch’ message will be displayed until database synchronization is complete, followed by turning system power off, then on. Synchronization can be monitored on the AUX- SYSTEM STATUS Page. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 169 Appendix In some cases it may be necessary to obtain an unlock code from Garmin in order to make the database product functional. It may also be necessary to have the system configured by a Garmin authorized service facility in order to use some database features.
  • Page 170 Turn the system OFF and remove the SD card from the top card slot. Repeat steps 2 through 10 for the other display. Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 171 SD card for each display, or to one display only for automatic synchronization to the other card(s) 3) Put the removed Garmin SD Card(s) back in the bottom SD card slot(s). 4) Turn the system ON. 5) During MFD power-up, check the MFD Power-Up screen and make sure that the database is initialized and shown on the database information.
  • Page 172 . ( The FliteCharts or ChartView database must only be installed on the MFD SD Card). 3) Put the Garmin SD Cards back in the bottom SD card slots of each flight display unit. 4) Turn the system ON.
  • Page 173 Appendix Uploading Database to GRS1 2) When the upload is complete the system is ready for use. 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 174 Appendix Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 175 ChartView 80, 81 Checklists 99–100 CLD TOP Softkey 56 Gain 69 Clearance player 11 Garmin Connext 47, 48, 53, 54 Clearance Recorder 11 Garmin Connext Weather 49 Index-1 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...
  • Page 176 NAV1 1, 10 Strike 43 NAV2 1, 10 Strike mode 44 Navigation database 19, 20 SVT 79, 136 NEXRAD 45, 142, 147 Synchronization 149 NEXRAD Softkey 55 Index-2 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 177 Vertical track 112 Video 97 VNV 17, 104 Vspeed 2 WAAS 131 WATCH® 70 Waypoint Selection Submenu 27, 28 Weather Attenuated Color Highlight 70 Weather data link page 45 Index-3 190-01896-01 Rev. A Garmin G1000 Cockpit Reference Guide for the Diamond DA62...

  • Page 178: Index

    Index Blank Page Index-4 Garmin G1000 Cockpit Reference Guide for the Diamond DA62 190-01896-01 Rev. A...
  • Page 180 Fax: +44 (0) 238 052 4004 Aviation Support: +44 (0) 370 850 1243 Garmin Corporation No. 68, Zhangshu 2nd Road Xizhi District, New Taipei City, Taiwan p: 34-93-357-2608 f: 34-93-429-4484 www.garmin.com 190-01896-01 Rev. A © 2015, 2016 Garmin Ltd. or its subsidiaries...

Table of Contents