Sony PDW-R1 Operation Manual page 50

DATA DATA DATA DATA
VITC VIUB COUNTER HOLD
dB OVER dB OVER dB OVER dB OVER
0 0 0 0
PB NDF EXT-LK
-12 -12 -12 -12
-20 -20 -20 -20
-30 -30 -30 -30 HOURS MINUTES SECONDS
-40 -40 -40 -40
-60 -60 -60 -60 DISC E
CH- 15 CH- 26 CH- 37 CH- 48 BATT E
PROCESS
AUDIO CONTROL
VIDEO
INPUT CH INPUT SEL INPUT SEL STATUS CHARACTER
WARNING KEY INHI REC INHI
OFF ON
5 1
MENU button
KEY INHI TC
ON
INT PRESET F-RUN
NETWORK
LOCAL EXT
ACCESS REMOTE RP188 REGEN R-RUN
OFF
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
AUDIO
PREV PLAY NEXT STOP
F REV F FWD
TOP END
1
With the SHIFT button held down, press the STATUS
button.
The process control screen
panel.
PROCESS CONTROL
VIDEO VAR ----- -----
CHROMA VAR ----- -----
BLACK PRE ----- -----
CHROMA-Ph PRE ----- -----
SYNC-Ph PRE ----- -----
SC-Ph PRE
KEY ASIGN : MENU
ADJUST : KEY+JOG DIAL
PREST/VAR : KEY+RESET
EXIT : STATUS
1) When the line mode is 525(U)/525(J), SETUP appears instead of
BLACK.
Notes
• Do the following operations within 30 seconds. The
screen returns to the normal screen if no operation is
done for 30 seconds.
• The process control screen does not appear if either
of the following is true.
- The unit is being controlled from a device
connected to the REMOTE connector, and basic
menu item 006 "LOCAL FUNCTION ENABLE"
is set to "dis" or "st&ej."
- The unit is connected to a computer by FAM or
FTP, and the computer is logged in to this unit.
To check the assignments to buttons which
select parameters
50
4-2 Playback
Video panel
VITC
FRAMES
B
F
LIGHT MONITOR
OFF ON OFF L H
4
SHUTTLE JOG
SUB THUMB
COUNTER
CLIP NAIL SHIFT
SEL HOLD
CLIP
ESSENCE
MENU
MARK
METER MONITOR
MENU SET RESET
SEL SEL
L/ST/R
SYSTEM S.SEL
MENU
MARK1
REC
IN OUT
MARK2
3
1)
appears in the video
V
000
A list of button assignments appears at the bottom of
the screen when you keep the MENU button pressed.
PROCESS CONTROL
VIDEO
CHROMA
BLACK
CHROMA-Ph PRE ----- -----
SYNC-Ph
SC-Ph
PREV:VIDEO
PLAY:CHROMA
NEXT:SETUP or BLACK
STOP:CHROMA-ph
List of parameters assigned to buttons
2
Hold down the following buttons and press the RESET
button to select "PRE" (PRESET: factory preset
setting) or "VAR" (VARIABLE: adjustable setting).
Each press of the button switches between "PRE" and
"VAR."
Button Parameter
PREV Video output level
PLAY Chroma output level
NEXT Setup/black level
STOP Chroma phase
G Output signal sync
phase
g Output signal
subcarrier phase
a) Underlined values are the factory defaults.
The figure below is an example of the screen that
appears when you hold the PLAY button down.
PROCESS CONTROL
CHROMA PRE ----- -----
Select "PRE" or "VAR"
V
VAR ----- -----
VAR ----- -----
PRE ----- -----
PRE ----- -----
PRE 000
(<):SYS-Ph
(>):SC-Ph
a)
Adjustment range
–512 to 0 to 511
–512 to 0 to 511
–512 to 0 to 511
–128 to 0 to 127
–128 to 0 to 127
0 to 511
V
000
Setting
Marker indicating the
position of the setting in
the adjustment range