Recording Operation; Auto Clip List Recording For Automatic; Lists - Sony PDW-R1 Operation Manual

To directly record SMPTE RP-188 LTC in an SDI
signal
Connect an SDI signal containing SMPTE RP188
LTC to the SDI IN connector. Press the VIDEO
INPUT SEL button and, while viewing the time data
display or the video panel, select SDI.
2
Set the PRESET/REGEN switch to PRESET, and set
the INT/EXT/RP188 to one of the following.
To record TC input to the TC IN connector, or
i.LINK TC: EXT
To record SMPTE RP188 LTC: RP188
For details of menu setting operations, see Chapter 7
"Menus" (page 89).

4-1-3 Recording Operation

To record, proceed as follows.
KEY INHI TC
ON
NETWORK INT PRESET F-RUN
LOCAL EXT
ACCESS REMOTE
RP188 REGEN R-RUN
OFF
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
AUDIO
PREV PLAY NEXT STOP
F REV F FWD
TOP END
2 3
1
Insert a disc.
For details, see 3-6-4 "Loading and Unloading a
Disc" on page 38.
2
Hold down the REC button, and press the PLAY
button.
Recording starts.
3
To stop recording, press the STOP button.
If the disc becomes full
Recording stops and the message "ALARM DISC END."
appears on the video panel.
Notes
• The shortest clip that can be recorded is 2 seconds long.
Even if recording start and stop operations are performed
within 2 seconds, a 2-second clip is recorded.
• The maximum number of clips that can be recorded is
300. If the loaded disc already contains 300 clips,
recording with the REC button is not possible. (The
message "Disc Full!" appears in the time data display.)
48
4-1 Recording
SHUTTLE JOG
SUB THUMB
COUNTER
SHIFT
CLIP NAIL
SEL HOLD
CLIP ESSENCE
MENU MARK
METER MONITOR
MENU SET RESET
SEL SEL
L/ST/R
SYSTEM
S.SEL
MENU
MARK1
REC
IN OUT
MARK2
• Do not allow the unit's primary power to be lost during
1)
recording. This could cause the clip being recorded to
be lost. (See 3-6-7 "Handling of Discs When Recording
Does Not End Normally (Salvage Function)" on page
40.)
1) Primary power is lost when the AC power switch on the rear panel is
turned off, the AC power cord is disconnected, DC power is turned off, the
battery pack is exhausted, the battery pack is removed, and so on.
To record essence marks
A shot mark 1 essence mark or shot mark 2 essence mark
is recorded if you hold down the F/MARK1 or f/MARK2
button and press the SET button during recording.
4-1-4 Auto Clip List Recording for
Automatic Inclusion of
Recorded Clips in Clip Lists
Auto clip list recording is a function for automatically
including the clips generated by recording operations in a
selected clip list. The updated clip list is saved to the disc.
Proceed as follows.
1
Insert a disc.
2
Load a clip list from the disc.
• To create a new clip list, load a NEW FILE (empty)
clip list.
• To add clips to an existing clip list, load that clip list.
For operations, see 5-3-1 "Loading a Clip List From
Disc Into Unit Memory" (page 68).
3
Press the SUBCLIP button, turning it on.
The unit enters auto clip list recording mode, and the
number of the clip list which is loaded in the current
clip list appears.
4
Press the REC button to start recording.
A clip is generated automatically from the video and
audio recorded in the interval from start to stop of
recording, and added as a sub clip to the current clip
list. When recording stops, the updated clip list is
written to disc.
5
Repeat the process of recording and stopping until you
have included all the required clips.
To change the registered clip list, repeat step 2 to load
the desired clip list.
To exit auto clip list recording mode
Press the SUBCLIP button, turning it off.