Hoshizaki IM-240DME Service Manual page 33

9) [F-series] 9) [F-series]
Locate the extension drain tube kit. Remove Locate the extension drain tube kit. Remove
the Locking Nut from the threaded section, and the Locking Nut from the threaded section, and
push the threaded pipe through the hole in the push the threaded pipe through the hole in the
side of the Bin. Align the Drain Pan, and insert side of the Bin. Align the Drain Pan, and insert
the Drain Pipe Collar and Packing into the free the Drain Pipe Collar and Packing into the free
end of tube kit and tighten. Secure the tube kit end of tube kit and tighten. Secure the tube kit
by re-attaching the Locking Nut and tightening by re-attaching the Locking Nut and tightening
to the Bin exterior. to the Bin exterior.
10) Before stacking, remove the clear plastic cover 10) Before stacking, remove the clear plastic cover
on the upper or middle unit wiring channel. on the upper or middle unit wiring channel.
Disconnect the Bin Control Switch leads (with Disconnect the Bin Control Switch leads (with
three-way plug). Remove the screws and the three-way plug). Remove the screws and the
Bin Control Switch. When stacking two or three Bin Control Switch. When stacking two or three
icemakers, this switch will not be required. icemakers, this switch will not be required.
Keep it after removal. See Fig. 12. Keep it after removal. See Fig. 12.
11) Attach the upper or middle unit on the lower 11) Attach the upper or middle unit on the lower
unit. See Fig. 13. unit. See Fig. 13.
12) Secure the two units with the two bolts and the 12) Secure the two units with the two bolts and the
two nuts provided. See Fig. 13. two nuts provided. See Fig. 13.
13) Align the lower unit drain hole and the upper 13) Align the lower unit drain hole and the upper
unit drain pan hole. Insert the Packing (lower unit drain pan hole. Insert the Packing (lower
unit accessory) and fasten the Drain Pipe Collar unit accessory) and fasten the Drain Pipe Collar
(lower unit accessory). See Fig. 13. (lower unit accessory). See Fig. 13.
14) Place the Ice Chute (lower unit accessory) and 14) Place the Ice Chute (lower unit accessory) and
secure it to the Bracket with the two screws. secure it to the Bracket with the two screws.
15) Connect the leads (with three-way plug) located 15) Connect the leads (with three-way plug) located
in the lower unit wiring channel to the upper or in the lower unit wiring channel to the upper or
middle unit receptacle, unplugged in the above middle unit receptacle, unplugged in the above
step 10). Secure the leads using the plastic step 10). Secure the leads using the plastic
clamp provided. Place the plastic cover in clamp provided. Place the plastic cover in
position. See Fig. 14. position. See Fig. 14.
16) Replace the icemaker panels in their correct 16) Replace the icemaker panels in their correct
positions. positions.
Note: Note: If stacking three icemakers, repeat the instructions 10) - 16) for the upper unit. If stacking three icemakers, repeat the instructions 10) - 16) for the upper unit.
Remember, only ONE Remember, only
Control extension leads are pre-wired with the plug and will be found coiled in the X- Control extension leads are pre-wired with the plug and will be found coiled in the X-
type wiring channel. type wiring channel.
E1CG4880210 E1CG4880210
ONE Bin Control is needed regardless of configuration. The Bin Bin Control is needed regardless of configuration. The Bin
29 29
Upper Unit Upper Unit
Remove Bin Control Switch Remove Bin Control Switch
Fig. 12 Fig. 12
Upper Unit Upper Unit
Drain Pipe Collar Drain Pipe Collar
Packing Packing
Drain Pan Drain Pan
Drain Outlet Drain Outlet
Lower Unit Lower Unit
Fig. 13 Fig. 13
Receptacle Receptacle
Plug Plug
Upper Unit Upper Unit
Lower Unit Lower Unit
Fig. 14 Fig. 14
Leads Leads
Screw Screw
Disconnect Disconnect
Screw Nut Screw
Nut
Ice Chute Ice Chute
Bolt Bolt
Ice Chute Ice Chute
Bracket Bracket
Wiring Channel Wiring Channel
Plastic Clamp Plastic Clamp