Hoshizaki IM-240DME Service Manual page 32

4. STACKING ICEMAKERS - IM-240D, IM-240X ONLY 4. STACKING ICEMAKERS - IM-240D, IM-240X ONLY
Check the icemaker models. A D-type icemaker and an X-type icemaker will Check the icemaker models. A D-type icemaker and an X-type icemaker will
be required for stacking two icemakers. A D-type icemaker and two X-type be required for stacking two icemakers. A D-type icemaker and two X-type
icemakers will be required when stacking three icemakers. The D-type icemaker icemakers will be required when stacking three icemakers. The D-type icemaker
is designed for the upper unit, and the X-type for the middle and lower units. is designed for the upper unit, and the X-type for the middle and lower units.
The D-type and X-type icemakers are provided with two different types of Bin The D-type and X-type icemakers are provided with two different types of Bin
Control Switch. Use the Bin Control Switch of the lower X-type icemaker only Control Switch. Use the Bin Control Switch of the lower X-type icemaker only
when stacking icemakers. The Bin Control Switch must be removed from the when stacking icemakers. The Bin Control Switch must be removed from the
upper (and middle) units. Connection of the Bin Control from the lower (and upper (and middle) units. Connection of the Bin Control from the lower (and
middle) to the upper unit will require additional connecting leads which are middle) to the upper unit will require additional connecting leads which are
supplied with the X-type icemaker. Misconnection or no connection may cause supplied with the X-type icemaker. Misconnection or no connection may cause
serious damage to the icemaker units, resulting in failure. serious damage to the icemaker units, resulting in failure.
1) Prepare and position the Storage Bin as detailed in 1) and 2) in "3. INSTALLATION". 1) Prepare and position the Storage Bin as detailed in 1) and 2) in "3. INSTALLATION".
2) Remove the icemaker panels. The Rear Panel is not required to be removed for installation. 2) Remove the icemaker panels. The Rear Panel is not required to be removed for installation.
See "1. UNPACKING". See "1. UNPACKING".
3) Move the icemaker carefully to prevent damage to the icemaker frame. 3) Move the icemaker carefully to prevent damage to the icemaker frame.
4) Remove the shipping tape holding the Drain 4) Remove the shipping tape holding the Drain
Pan. Pan.
5) Attach the lower unit (X-type) on the top of the 5) Attach the lower unit (X-type) on the top of the
Storage Bin. See Fig. 10. Storage Bin. See Fig. 10.
6) Secure the lower unit with the two bolts and two 6) Secure the lower unit with the two bolts and two
plastic washers provided. See Fig. 10. plastic washers provided. See Fig. 10.
7) Remove the shipping tape holding the Bin 7) Remove the shipping tape holding the Bin
Control Switch on the Drain Pan. Attach the Control Switch on the Drain Pan. Attach the
Bin Control Switch to the frame located at the Bin Control Switch to the frame located at the
left bottom of the condensing unit, and secure left bottom of the condensing unit, and secure
it using the two screws and the two washers it using the two screws and the two washers
provided. See Fig. 11. provided. See Fig. 11.
8) [P-200SD] 8) [P-200SD]
Align the drain hole and the drain pan hole. Align the drain hole and the drain pan hole.
Insert the Packing (bin accessory) and fasten Insert the Packing (bin accessory) and fasten
the Drain Pipe Collar (bin accessory) tightly, the Drain Pipe Collar (bin accessory) tightly,
within the recommended torque of 39.2 N·m. within the recommended torque of 39.2 N·m.
See Fig. 10. See Fig. 10.
WARNING WARNING
Lower Unit Lower Unit
Drain Pipe Collar Drain Pipe Collar
Extension Extension
Extension Extension
Drain Hole Drain Hole
Drain Pan Drain Pan
28 28
Bolt Bolt
Bolt Bolt
Packing Packing
Washer Washer
Drain Pan Drain Pan
Fig. 10 Fig. 10
Bin Control Switch Bin Control Switch
Handle with care Handle with care
Screw Screw
Washer Washer
Bin Control Switch Bin Control Switch
Fig. 11 Fig. 11
Frame Frame
E1CG4880210 E1CG4880210