Troubleshooting; Replacement Parts - Montigo 30FIDNIL-01 Installation & Maintenance Manual

Troubleshooting

SIT Proflame 2:
PROBLEM SOLUTION
Pilot Igniter won't 1. Check the master override switch and turn ON
spark
2. Ensure main power is ON and new batteries are installed in
the remote control and backup battery pack
3. Make sure remote is synced with control board.
4. Check the 3.15A fuse in the control box and replace if
necessary
5. Make sure remote is not in smart or thermostat mode.
6. Check ignitor wire is connected to the control board and is
not damage
Pilot Igniter 1. Verify the Inlet and Manifold Gas Pressure are within
sparking, but Pilot acceptable limits
burner will not light
2. Check all connections to gas valve
3. Check fuel supply valves and emergency shut off valve is
open
4. Check wiring connections from control board to valve
Pilot lights , but 1. Check and verify all wiring connections as per the wiring
Main burner will not diagram.
Light
2. Verify the inlet and Manifold Pressure are within acceptable
limits
Fans not working 1. Ensure main power is ON and is plugged in (fireplace may be
operating on back up batteries).
2. Check the 3.15A fuse in the control box and replace if
necessary
3. Make sure fans are plugged into the control board

Replacement Parts

NG Gas Valve
Propane Gas Valve
Replacement Burner
NG Pilot
Propane Pilot
Replacement Screen
Proflame 2 Control Module
Replacement Halogen Bulbs
Replacement Fuse
Replacement Fan Kit
Replacement ECO Fan Kit
Conversion Kit (NG to Propane)
Red Brick Panel Set
Brown Brick Panel Set
Porcelain Panel Kit
Standard Faceplate
4 Sided Faceplate
Oversized Faceplate
Standard Trim Offset Kit
Door
Log Set
XG0528 - 170223
SIT IPI Proflame 2 - Replacement Parts List
30FID-S 30FID-L
RGCA002 RGCA002
RGCA004 RGCA004
RB30FID-S RB30FID-L
RPA040 RPA041
RPA043 RPA045
RSC30FID RSC30FID
RGC3095 RGC3095
REC1416 REC1416
REC1386 REC1386
RFKFID RFKFID
RFKFIDECO RFKFIDECO
GCA003 GCA003
BRK30FIR
BRK30FIB
RPP30FID RPP30FID
FP30FID-01 FP30FID-01
FP30FID4S-01 FP30FID4S-01
FP30FIDOS-01 FP30FIDOS-01
FP30FIDOF FP30FIDOF
RDR30FID RDR30FID
LGS30FI
PROBLEM
Lights not working
Pilot lights , but
Main burner will
not Light and igniter
continues to spark
Control module
beeps twice when
On/Off button on
remote is pressed
and Red LED is On
34FID-S 34FID-L
RGCA002 RGCA002
RGCA004 RGCA004
RB34FID-S RB34FID-L
RPA042 RPA041
RPA044 RPA045
RSC34FID RSC34FID
RGC3095 RGC3095
REC1416 REC1416
REC1386 REC1386
RFKFID RFKFID
RFKFIDECO RFKFIDECO
GCA006 GCA006
BRK34FIR
BRK34FIB
RPP34FID RPP34FID
FP34FID-01 FP34FID-01
FP34FID4S-01 FP34FID4S-01
FP34FIDOS-01 FP34FIDOS-01
FP34FIDOF FP34FIDOF
RDR34FID RDR34FID
LGS34FI
Appendix
SOLUTION
1. Ensure main power is ON and is plugged in (fireplace may be
operating on back up batteries).
2. Check the 3.15A fuse in the control box and replace if
necessary
3. Make sure fans are plugged into the control board
4. Bulbs are burnt out
1. Check the Pilot Flame Sensor Rod and clean with steel wool
or similar.
2. Check the Pilot hood and clean with steel wool if dirty.
3. Check flame sensor wire is plugged control board and is not
damaged
4. Adjust pilot flame using the pilot adjustment screw if the pilot
flame is too long or too short (Flame should fully engulf the
sensor rod and must be stable)
5. Check supply pressure
6. Check and make sure the ground wire from the pilot is
connected to the fireplace body
1. Replace batteries in battery pack
47