Mitsubishi Electric FR-F820-00046 Instruction Manual page 316

Setting
Signal
Positive Negative
name
logic logic
49 149 Y49
50 150 Y50
51 151 Y51
52 152 Y52
53 153 Y53
54 154 Y54
57 157 IPM
64 164 Y64
65 165 Y65
66 166 ALM3
67 167 Y67
68 168 EV
70 170 SLEEP
71 171 RO1
72 172 RO2
73 173 RO3
74 174 RO4
75 175 RIO1
76 176 RIO2
77 177 RIO3
78 178 RIO4
79 179 Y79
80 180 SAFE
82 182 Y82
85 185 Y85
86 186 Y86
87 187 Y87
88 188 Y88
89 189 Y89
90 190 Y90
Function
During pre-charge operation
During second pre-charge
operation
Pre-charge time over
Second pre-charge time over
Pre-charge level over
Second pre-charge level over
PM motor control
During retry
Emergency drive in
*2
operation
Fault output during emergency
*2
drive
*3
Power failed
24 V external power supply
operation
PID output interruption
Commercial power supply side
motor 1 connection RO1
Commercial power supply side
motor 1 connection RO2
Commercial power supply side
motor 1 connection RO3
Commercial power supply side
motor 1 connection RO4
Inverter side motor 1
connection RIO1
Inverter side motor 1
connection RIO2
Inverter side motor 1
connection RIO3
Inverter side motor 1
connection RIO4
Pulse train output of output
power
Safety monitor output
BACnet binary output
*2
DC current feeding
Control circuit capacitor life
*5
(for Pr.313 to Pr.322)
Main circuit capacitor life
*2*5
(for Pr.313 to Pr.322)
Cooling fan life
*5
(for Pr.313 to Pr.322)
Inrush current limit circuit life
*2*5
(for Pr.313 to Pr.322)
Life alarm
Operation
Outputted while the pre-charge function is
working.
Outputted when the time period while the pre-
charge function is working reaches the time
limit set in Pr.764 or Pr.769.
Outputted when the value higher than the
detection level set in Pr.763 or Pr.768 is
measured until the pre-charge function stops
during pre-charge operation.
Outputted while the operation is performed
under PM motor control.
Outputted during retry operation.
Outputted during emergency drive operation. Pr.514, Pr.515,
Outputted when a fault occurs during
emergency drive operation.
Outputted when the inverter power output is
shut off due to power failure or undervoltage
or when the power failure time deceleration-
to-stop function is activated.
Outputted while the inverter operated with a
24 V power supplied from an external source.
Outputted while PID output suspension
function is activated.
Outputted depending on the motor drive
conditions when the multi-pump function is
used.
Outputted in pulses every time the
cumulative value of energy outputted from
the inverter reaches the Pr.799 setting.
Outputted while the safety stop function is
activated.
Enables output from the Binary Output object
for BACnet communication.
Outputted during power failure or
undervoltage of the AC power supply.
Outputted when the control circuit capacitor
approaches the end of its life.
Outputted when the main circuit capacitor
approaches the end of its life.
Outputted when the cooling fan approaches
the end of its life.
Outputted when the inrush current limit circuit
approaches the end of its life.
Outputted when any of the control circuit
capacitor, main circuit capacitor, inrush
current limit circuit, or the cooling fan
approaches the end of its life.
5.8 (M) Item and output signal for monitoring
Refer
Related
to
1
parameter
page
2
Pr.127 to Pr.134,
Pr.241, Pr.553,
Pr.554, Pr.575 to 425
Pr.577, Pr.753 to
3
Pr.769, C42, C45
4
Pr.71 to Pr.80,
174
Pr.998
Pr.65 to Pr.69 261
5
Pr.523, Pr.524, 263
Pr.1013
6
Pr.261 to Pr.266 458
7
— 69
Pr.127 to Pr.134,
401
Pr.575 to Pr.577
8
9
Pr.575 to Pr.591 430
10
Pr.799 328
— 70
Pr.549 511
Pr.30 539
Pr.255 to Pr.259 208
315
5. PARAMETERS