Emlxs.conf Parameter Example - Fujitsu ETERNUS DX Configuration Manual

Chapter 1 Operations When Using Oracle Fibre Channel Cards
1.5 Required Driver Parameters
1.5.3

emlxs.conf Parameter Example

A switch connection example is shown below.
# COPYRIGHT
# Solaris LightPulse emlxs driver: global initialized data.
#
# console-notices:
# console-warnings: Sets the verbose level for driver warnings to the console.
# console-errors:
#
# log-notices:
# log-warnings: Sets the verbose level for driver warnings to the system log file*.
# log-errors:
#
# *NOTE:
#
# Each parameter is a bit mask that enables/disables specific types of messages.
# If the bit is set, then the messages of that type are enabled.
#
# The available message types are listed below:
#
# LOG_MISC
# LOG_DRIVER
# LOG_INIT
# LOG_MEM
# LOG_SLI
# LOG_MBOX
# LOG_NODE
# LOG_LINK
# LOG_ELS
# LOG_PKT
# LOG_FCP
# LOG_TGTM
# LOG_IP
# LOG_SFS
# LOG_IOCTL
# LOG_FIRMWARE
# LOG_CT
# LOG_FCSP
# LOG_RESERVED
#
# Range: Min:0
#
# console-notices
# console-warnings = 0;
# console-errors
#
# log-notices
# log-warnings = 0xffffffff;
# log-errors
#
console-notices=0;
console-warnings=0;
console-errors=0;
log-notices=0xffffffff;
log-warnings=0xffffffff;
log-errors=0xffffffff;
# num-iocbs:
#
# Range: Min:128
#
num-iocbs=1024;
# ub-bufs:
#
# Range: Min:40
#
ub-bufs=1000;
#
# +++ Variables relating to IP networking support. +++
#
# network-on:
#
# 0 = Disables IP networking support in the driver.
# 1 = Enables IP networking support in the driver.
#
# Range: Min:0
#
network-on=1;
#
# +++ Fibre Channel specific parameters +++
#
# topology:
#
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
E004-2008 Emulex. All rights reserved.
Sets the verbose level for driver notices to the console.
Sets the verbose level for driver errors to the console.
Sets the verbose level for driver notices to the system log file*.
Sets the verbose level for driver errors to the system log file*.
The system log file is normally found at /var/adm/messages.
0x00000001 /* Misc events */
0x00000002 /* Driver attach and detach events */
0x00000004 /* HBA initialization events */
0x00000008 /* Memory management events */
0x00000010 /* Service Level Interface (SLI) events */
0x00000020 /* Mailbox events */
0x00000040 /* Node events */
0x00000080 /* Link events */
0x00000100 /* ELS events */
0x00000200 /* General I/O packet events */
0x00000400 /* FCP traffic events */
0x00000800 /* FCP target mode events */
0x00001000 /* IP traffic events */
0x00002000 /* SFS events */
0x00004000 /* IOCtl events */
0x00008000 /* Firmware download events */
0x00010000 /* CT events */
0x00020000 /* FCSP events */
0xfffc0000 /* Reserved for future use */
Max:0xffffffff
= 0; (Default)
(Default)
= 0; (Default)
= 0xffffffff; (Default)
(Default)
= 0xffffffff; (Default)
Sets the number of iocb buffers to allocate.
Max:10240 Default:1024
Sets the number of unsolicited buffers to be allocated.
Max:16320 Default:1000
Enable/Disable IP networking support in the driver.
Max:1 Default:1
link topology for initializing the Fibre Channel connection.
Copyright 2017 FUJITSU LIMITED
23
P3AM-6312-18ENZ0