Fujitsu ETERNUS DX Configuration Manual page 50

Chapter 2 Setup Procedure for Emulex Fibre Channel Cards
2.5 Required Driver Parameters
2.5.2.2 /kernel/drv/lpfc.conf Example
A switch connection example is shown below.
#
# Copyright (c) 2005, Emulex
# 3333 Susan Street, Costa Mesa, CA 92626
#
# All rights reserved. This computer program and related documentation
# is protected by copyright and distributed under licenses restricting
# its use, copying, distribution and decompilation. This computer
# program and its documentation are CONFIDENTIAL and a TRADE SECRET
# of Emulex Design & Manufacturing Corporation. The receipt or possession
# of this program or its documentation does not convey rights to reproduce
# or disclose its contents, or to manufacture, use, or sell anything that
# it may describe, in whole or in part, without the specific written consent
# of Emulex Design & Manufacturing Corporation. Any reproduction of this
# program without the express written consent of Emulex Design & Manufacturing
# Corporation is a violation of the copyright laws and may subject you to
# criminal prosecution.
#
#
# Solaris LightPulse lpfc (SCSI) / lpfn (IP) driver: global initialized data.
#
# lpfc.conf 1.29.1.2 2005/10/21 11:06:55PDT
# Verbosity:
# deluged with LOTS of information.
# You can set a bit mask to record specific types of verbose messages:
#
# 0x1 ELS events
# 0x2 Device Discovery events
# 0x4 Mailbox Command events
# 0x8 Initialization events
# 0x10 Link Attention events
# 0x20 IP events
# 0x40 FCP events
# 0x80 Node table events
# 0x400 Miscellaneous events
# 0x800 SLI events
# 0x2000 IOCtl events
# 0xffff Log All Events
log-verbose=0x0;
# Setting log-only to 0 causes log messages to be printed on the
# console and to be logged to syslog (which may send them to the
# console again if it's configured to do so).
# Setting log-only to 1 causes log messages to go to syslog only.
log-only=1;
#
# +++ Variables relating to FCP (SCSI) support. +++
#
# specifies the method of binding to be used. This
# binding method is used for persistent binding and automaped
# binding. A value of 1 will force WWNN binding, value
# of 2 will force WWPN binding, value of 3 will force
# DID binding and value of 4 will force the driver to derive
# binding from ALPA (hard addressed) in a private loop environment.
# Any persistent binding whose type does not match with the
# bind method of the port will be ignored.
lpfc0-fcp-bind-method=2;
lpfc1-fcp-bind-method=2;
# Setup FCP persistent bindings,
# fcp-bind-WWPN binds a specific WorldWide PortName to a target id,
# fcp-bind-WWNN binds a specific WorldWide NodeName to a target id,
# fcp-bind-DID binds a specific DID to a target id.
# Binding method must match with the bind method of that HBA, else the
# binding will be ignored.
# fcp-bind-method should NOT be set to 4 when one of these binding methods
# is used.
# WWNN, WWPN and DID are hexadecimal values.
# WWNN must be 16 digit BCD with leading 0s.
# WWPN must be 16 digit BCD with leading 0s.
# DID must be 6 digit BCD with leading 0s.
# The SCSI ID to bind to consists of two parts, the lpfc interface
# to bind to, and the target number for that interface.
# Thus lpfc0t2 specifies target 2 on interface lpfc0.
# NOTE: Target ids, with all luns supported, must also be in sd.conf.
# Here are some examples:
#
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
only turn this flag on if you are willing to risk being
For direct connections, lpfc0-fcp-bind-method=4;
WWNN SCSI ID
Copyright 2017 FUJITSU LIMITED
50
P3AM-6312-18ENZ0