Fujitsu ETERNUS DX Configuration Manual page 25

Chapter 1 Operations When Using Oracle Fibre Channel Cards
1.5 Required Driver Parameters
# 0 = Disables power management support in the driver.
# 1 = Enables power management support in the driver.
#
# Range: Min:0
#
pm-support=0;
# num-nodes:
#
# 0 = Indicates auto detect limit of adapter.
#
# Range: Min:0
#
num-nodes=0;
# pci-max-read:
#
# This value controls the adapter's max PCI-X memory read count.
# On Sunfire x4100/4200 systems this parameter must be changed to
# 1024 bytes.
# Sunfire x4100/4200 systems due to the unique nature of the PCI-X bus
# on these systems, otherwise it should be left as default.
#
# Options:
#
# Range: Min:512
#
# *Uncomment this parameter for Sunfire x4100/4200 systems only
#pci-max-read=1024;
# linkup-delay:
#
# This value controls how long the driver waits for the Fibre Channel
# link to come up after an adapter reset before continuing normal operation.
#
# Range: Min:0
#
linkup-delay=10;
# enable-npiv:
#
# Requires SLI3 mode support in the adapter firmware.
#
# Range: Min:0
#
enable-npiv=0;
# vport-restrict-login:
#
# Requires SLI3 mode support in the adapter firmware.
# Requires enable-npiv parameter to be set to 1.
#
# Range: Min:0
#
vport-restrict-login=1;
# vport: Virtual port registration table.
# The enable-npiv must be set to 1.
#
# The vport table may have any number of comma delimited entries.
# Each entry must be of the form:
#
# "PHYS_WWPN:VPORT_WWNN:VPORT_WWPN:VPORT_ID"
#
# PHYS_WWPN
# VPORT_WWNN = Desired World Wide Node Name of virtual port
# VPORT_WWPN = Desired World Wide Port Name of virtual port
# VPORT_ID
#
#
#
# Example:
#
# vport="10000000c9123456:28010000c9123456:20010000c9123456:1",
# "10000000c9123456:28020000c9123456:20020000c9123456:2",
# "10000000c9123457:28010000c9123457:20010000c9123457:1",
# "10000000c9123457:28020000c9123457:20020000c9123457:2",
# "10000000c9123457:28030000c9123457:20030000c9123457:3";
#
# enable-auth:
#
# Range: Min:0
#
enable-auth=0;
# max-xfer-size:
# This parameter is only used by the driver on i386 platforms.
# The driver does not limit transfer size on SPARC platforms.
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Max:1 Default:0
Number of fibre channel nodes (NPorts) the driver will support.
Max:4096 Default:0
Sets the PCI-X max memory read byte count on the adapter.
Currently, this parameter should only be modified on
512, 1024, 2048, 4096
Max:4096 Default:2048
Sets the linkup delay period (seconds) after initialization.
Max:60 Default:10
Enables NPIV support in the driver.
Max:1 Default:0
Restricts login to virtual ports to conserve resources.
Max:1 Default:1
= World Wide Port Name of adapter's physical port
= Desired virtual port id (1 to max vports)
The port ids must start at 1 and increment by 1
with no gaps in the count.
Enables DHCHAP support in the driver.
Max:1 Default:0
Sets the maximum SCSI transfer size in bytes per IO
Copyright 2017 FUJITSU LIMITED
25
P3AM-6312-18ENZ0