Message; Descriptor; Date - Fisher FIELDVUE DVC6200 Instruction Manual

Field Communicator Menu Trees
May 2013
Hot Key
1 Instrument Mode
2 Control Mode
3 Protection
4 Stabilize/Optimize
1
Configure
1 Guided Setup
2 Detailed Setup
3 Calibrate
Online
1 Configure
2 Service Tools
3 Overview
1
HART Application
1 Offline
2 Online
3 Utility
4 HART Diagnostics
Notes:
1‐1‐1 indicates fast‐key sequence to reach menu
1
This menu is available by pressing the left
arrow key from the previous menu.
2
Instrument level AD, PD, and ODV only.
3
Instrument level ODV only.
4
Instrument level HC, AD, and PD only.
5
Instrument level HC only.
6
Fast key sequence for Alert Record with instrument level ODV is 1‐2‐3‐7.
1
130
Field Communicator Menu Tree for
Instrument Level HC, AD, PD, and ODV
1‐1
Guided Setup
1 Setup Wizard
2 Performance Tuner
2 Stabilize/Optimize
5
1‐2
Detailed Setup
1 Mode and Protection
2 Response Control
3 Alert Setup
4 Status
5 Instrument
6 Valve and Actuator
7 SIS/Partial Stroke
1‐2‐7
3
Partial Stroke
1 PST Enable
2 PST Vars View/Edit
1‐2‐6
Valve and Actuator
1 Manufacturer
2 Valve Serial Number
3 Valve Style
4 Actuator Style
5 Travel Sensor Motion
6 View/ Edit Feedback Connection
7 Assembly Specification Sheet
1‐3
Calibrate
1 Travel Calibration
2 Sensor Calibration
3 Relay Adjust
4 Restore Factory
4 Settings
2
Service Tools
1 Alert Conditions
2 Status
2‐3
3 Device Record
4 Stroke Valve
5 Partial Stroke Test 3
3
Overview
1 Analog In
2 Setpoint
3 Travel
4 Drive Signal
5 Pressure
6 Variables
7 Device Information
8 DD Information
3‐7
Device Information
1 HART Tag
2 Device ID
3 Manufacturer
4 Model
5 Device Revision
6 Firmware Revision
7 Hardware Revision
8 Instrument Level
9 HART Universal Revision
2 3
1‐2‐1
Mode and Protection
1 Instrument Mode
2 Control Mode
3 Restart Control Mode
4 Burst Mode
2 5 Protection
1‐2‐2
Response Control
1 Tuning
2 Travel/Pressure Control
3 Input Characterization
4 Custom Characterization Table
5 Dynamic Response
1‐3‐1
Travel Calibration
1 Auto Calibration
2 Manual Calibration
1‐3‐2
Sensor Calibration
1 Pressure Sensors
2 Analog In Calib
Instrument
Device Record
1 General
1 Maximum Recorded
2 Units
Temperature
3 Analog Input Range
2 Minimum Recorded
4 Relay Type
Temperature
5 Zero Power Condition
3 View Number of Days
6 Maximum Supply Pressure
Powered Up
7 Auxiliary Terminal Action
4 Number of Power Ups
8 Instrument Date and Time
9 Calib Status and Type
3‐5
Pressure
1 Pressure A
2 Pressure B
3 A minus B
4 Supply
2
3‐6
Variables
1 Auxiliary Input
2 Temperature
3 Maximum Recorded Temperature
4 Minimum Recorded Temperature
5 Cycle Counter
6 Travel Accumulator
7 Raw Travel Input
8 View Number of Days Powered Up
9 Number of Power Ups
4
Instruction Manual
D103409X012
1‐2‐1‐4
Burst Mode
1 Burst Enable
2 Change Burst Enable
3 Burst Command
4 Change Burst Command
5 Cmd 3 Configured Pressure
1‐2‐2‐1
Tuning
1 Travel Tuning
2 Integral Settings
3 Pressure Tuning
1‐2‐2‐2
Travel/Pressure Control
1 Travel/Pressure Select
2 Cutoffs and Limits
3 Pressure Control
4 End Pt Press Control
1‐2‐2‐5
Dynamic Response
1 SP Rate Open
2 SP Rate Close
3 View/Edit Lag Time
3 Lead/Lag
3
1‐2‐3
Alert Setup
1 Electronics Alerts
2 Sensor Alerts
3 Environment Alerts
4 Travel Alerts
5 Travel History Alerts
6 SIS Alerts 3
6 Alert Record
6
1‐2‐4
Status
1 Instrument Time
2 Calibration and Diagnostics
3 Operational
4 Integrator Saturation
1‐2‐5
1‐2‐5‐1
General
1 HART Tag
2 Message
3 Descriptor
4 Date
5 Valve Serial Number
6 Instrument Serial Number
7 Polling Address
1‐2‐5‐2
Units
1 Pressure Units
2 Temperature Units
3 Analog In Units
1‐2‐5‐3
Analog Input Range
1 Input Range Hi
2 Input Range Lo
1‐2‐5‐9
Calib Status and Type
1 Last AutoCal Status
2 Last Calibration Type
5
4
6