100% Read Adjustment; Original Registration & Ccd Read Adjustments; Adf 100% Image 1-Sided Adjustment - Panasonic DP-3030 Service Manual

5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm.
6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.
7. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
3.8.4.

100% Read Adjustment

1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION", "ORIGINAL SIZE (LEDGER/A3)" and "3" keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust the Side to Side to be the
same.
7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
8. Perform the Service Mode F6-01 (Adj 100% Lead-Tail Read), to adjust the Top to End to be the
same.
9. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
Note:
This is the size adjustment and do not worry about the positioning.
3.8.5. Original Registration & CCD Read Adjustments
1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION", "ORIGINAL SIZE (LEDGER/A3)" and "3" keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-03 (Original Registration), to adjust the Original Registration.
7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value.
8. Perform the Service Mode F6-53 (P Mode Image Density), to adjust the CCD Read for the side
position.
9. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
3.8.6.

ADF 100% Image 1-Sided Adjustment

1. Place the Original Document on the ADF.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION", "ORIGINAL SIZE (LEDGER/A3)" and "3" keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-93 (ADF 100% Image 1-Sided), to adjust the Side to Side to be the
same.
7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
8. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
Ver. 2.1
109
DP-2310/3010
DP-2330/3030
MAR 2005