Page 2
URL: http://www.senju-m.co.jp) is recommended when repairing PbF PCBs. The contents of this Service Manual and the Specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice. Published in Japan.
Page 3
Important Notice Please read this notice completely BEFORE installing any optional accessories. As failure to properly install the additional board or connector with the power ON (only the front power switch Off) could damage the copier's SPC or SC board. Please follow the instructions below: 1. It is essential that you turn OFF power to the Main Power Switch located in the rear of the copier. 2. It is essential that you unplug the Main AC Power Cord from the wall outlet. 3. Please carefully read the installation instructions and follow each step. <Example: DP-2330/3030> Note: If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from being performed (similar to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below when turning OFF the Power Switches on the machine. 1. Turn the Power Switch on the Left Side of the machine to the OFF position first. 2. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit. 3. Turn the Main Power Switch on the Back of the machine to the OFF position. (This interrupts all the power to the machine) 4. Unplug the AC Power Cord. * The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice.
Precautions For Your Safety To prevent severe injury and loss of life, read this section carefully before servicing the Panasonic machine to ensure proper and safe operation of your machine. Please ensure that the machine is installed near a wall outlet and is easily accessible.
Once a month, unplug the machine and check the power cord for the following. If you notice any unusual condition, contact your Service Provider. The power cord is plugged firmly into the receptacle. The plug is not excessively heated, rusted, or bent. The plug and receptacle are free of dust.
Page 6
CAUTION Operating Safeguards Do not place a magnet near the safety switch of the machine. A magnet can activate the machine accidentally, resulting in injuries. Do not use a highly flammable spray or solvent near the machine. It can cause fire. When copying a thick document, do not use excessive force to press it against the scanning glass.
DP-2310/3010 DP-2330/3030 1 Specifications Table 1.1. Copy Function Description Items Remarks DP-2310/2330 DP-3010/3030 Basic Specifications 1 Type Desktop 2 Platen Fixed 3 Original Position Platen Left / Rear ADF / i-ADF Left / Center 4 Recording Paper Path Center 5 Face Up / Face Down...
Page 9
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 17 Paper Feed Front Loading Universal Paper Tray Paper Tray Capacity 550 sheets x 2 LTR / A4 : 20 lb (75 g/m2) Auto Size Setting Control Panel Selectable Low Level Warning Empty Only...
Page 10
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 2 Cabinet Stand for Option Base Plate with Casters 4-Paper Tray Configuration Stand for Option Low Plain Stand 3-Paper Tray Configuration Stand for Option High Plain Stand 2-Paper Tray Configuration For EU and Other...
Page 11
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Shift Tray Function No Manual Stapling. Not available with Rotation. Staple Function Not available with INV, INV-R, A5, A5-R or B5-R. Stapler Capacity 3,000 pins LTR, LTR-R, A4, A4-R, B5 : Max. Number of Pages...
Page 12
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Reservation while Power On Auto Start Initial Energy Saver Automatically enters the Sleep or Shutdown Mode Standby Mode Yes (140Wh) after 15 minutes from the Standby or Energy Saver Mode. Manually enters the Energy...
Page 13
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Others (Inverting ADF & ADU) LDR → LTR x 2 2-Page Copy Mode (A3 → A4 x 2, B4 → B5 x 2) 2 in 1 4 in 1 6 in 1 For USA and Canada...
Page 14
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Electronic Counter Digital Sky Shot Mode Check / Slip Mode 3 Control Panel Display Wide Touch Panel LCD GREEN : Scanning / Status Lamp Printing : Alarm / Warning Original Size Copy Size...
Page 15
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Finishing Warning Indicators Add Toner Toner Waste Container Full Add Paper (No Paper) Add Paper (Under 50 sheets) Paper Jam Indication Paper Jam Location Service Alert Call User Error Machine Error History of Jam Errors...
Page 16
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Efficiency 1 Productivity ADF Productivity (LTR / A4) 100% Inverting ADF 100% ADU Copy Productivity Throughput (LTR / A4) Transport Method Stack less When exiting to lower Inner 1→2 Tray from 1st Tray.
DP-2330/3030 1.2. Fax, Printer and Internet Fax Functions 1.2.1. Fax Function Description Items Remarks DP-2310/2330 DP-3010/3030 Main Specifications 1 Compatibility ITU-T Std & Non-Std 2 PSTN Line Port 1-Line Only 3 Leased Line Port 4 V.24 Line Port 5 Modem Speed 33.6 - 2.4kbps...
Page 19
DP-2310/3010 DP-2330/3030 Description Items Remarks DP-2310/2330 DP-3010/3030 Direct Dialing Voice mode (Monitor Dialing) 9 Automatic Redialing Up to 15 times at 0 to 15 min. intervals 10 Manual Redialing Pressing the REDIAL/PAUSE button 11 Line Monitor Speaker 12 Chain Dialing (Hybrid Dial)
DP-2310/3010 DP-2330/3030 1.2.2. Printer Function Description Items Remarks DP-2310/2330 DP-3010/3030 Interface 1 Centronics Parallel I/F Ethernet 10Base-T/ 2 LAN (Network) 100Base-TX 3 USB Port 4 IEEE-1394 Printer Function LDR, LGL, LTR, LTR-R, INV-R For USA and Canada 1 Printing Size...
Page 23
DP-2310/3010 DP-2330/3030 1.2.3. Network Scanner Function Description Items Remarks DP-2310/2330 DP-3010/3030 Interface 1 Centronics Parallel I/F Ethernet 10Base-T/ 2 LAN (Network) 100Base-TX 3 USB Port 4 IEEE-1394 Firewire Network Scanning Function 1 Scanning Device CCD (i-ADF / Platen) ITU-T Image No. 1 (A4, Std...
Page 24
DP-2310/3010 DP-2330/3030 1.2.4. Internet Fax Function Description Items Remarks DP-2310/2330 DP-3010/3030 Main Specifications 1 Communication Protocols SMTP / POP3 / MIME 2 Max. Modem Speed 3 Coding Scheme JBIG/MMR/MR/MH Selectable (PDF format can be used for Scan- to-Email when sending to a PC.
Page 25
8 DHCP Client Lightweight Directory Access 9 LDAP Protocol 10 TIFF Viewer Selectable, PDMS / TIFF Viewer Certainty Email from RCV side to Panasonic 1 Comm. Journal (w / Image) Internet FAX's only 1 Email Address Ver. 2.0 DEC 2004...
DP-2310/3010 DP-2330/3030 1.3. System Combination Inverting ADF (i-ADF) ADF PC Board Scanner Unit Document Sensor (SDR PC Board) Motor Panel Main PC Board PCL6 Fax Communication (PNL PC Board) (SC PC Board) Emulation Option Option (FXB) PS/PCL6 Printer Emulation Option Network Scanner Option Interface...
DP-2310/3010 DP-2330/3030 1.4. Options List Options ■ Option Name Option Number Remarks Printer Controller Module for PCL6 DA-PC300 For DP-2310 / 3010 Multi Page Description Language DA-MC300 Controller Module for PS/PCL6 Printer Controller Module for PCL6-IPX/ DA-PC301 For DP-2330 / 3030 (For USA and Canada, can also be used Multi Page Description Language for DP-2310 / 3010 without IPX/SPX)
Page 28
DP-2310/3010 DP-2330/3030 ■ Supplies Part Name Part Number Remarks Toner DQ-TU15E Staple Cartridge FQ-SS32 OPC Drum DQ-H60E Developer DQ-Z120E Note: PCL6 is a Page Description Language of the Hewlett-Packard Company. PS3 is a Page Description Language of the Adobe Systems Company. Available in Specified Destinations Ver.2.0 DEC 2004...
DP-2310/3010 DP-2330/3030 2 Maintenance, Adjustments and Check Points 2.1. Preventive Maintenance Preventive maintenance is performed at specific intervals and consists of machine cleaning and parts replacement. It is essential to perform these service activities properly and at the specified intervals for customer satisfaction.
Page 30
DP-2310/3010 DP-2330/3030 Laser Handling Precautions The optical laser system employed by this photocopier is completely sealed by a protective housing and an external cover. Therefore, the laser beam will not stray or leak during photocopying operation. However, when servicing the photocopier, take the following precautions: 1.
DP-2310/3010 DP-2330/3030 2.4. Preventive Maintenance Check List Cleaning Replacement/Adjustment Ref. Ref. Mechanical Parts Cycle Cycle Counter Method Procedure (Sheet) (Sheet) i-ADF/ADF Unit 1 ADF Roller 1728 Alcohol 120K Refer to F7-02-03 2.2.1. of the 2 Pre Feed Roller 1731 Alcohol 120K Service 3 Separation Roller...
Page 35
To verify the counter information, print the Total Counter List using the Service Mode: F7 - Electronic Counter - 00 (List Print). 3. Cleaning, Replacement and Adjustment Cycle (Sheet) are based on using Panasonic's recommended standard paper and supplies. These cycles may vary with the kind of paper used and/or ambient conditions.
DP-2310/3010 DP-2330/3030 2.5. Resetting the P/M (Preventive Maintenance) Counter When the machine reaches the preset P/M Cycle, it will show "Call for P/M" or "Replace The Toner Waste Container" on the LCD Display. The PM Counter can be reset by following the procedures below. 2.5.1.
DP-2310/3010 DP-2330/3030 2.6. Lubrication Point List This information is used for routine Preventive Maintenance (PM) calls to ensure the highest degree of reliability. Inspect the following areas and lubricate as required. The inspection interval is usually 120K copies or more, however the interval may be reduced due to environmental conditions. Ref.
Page 38
DP-2310/3010 DP-2330/3030 Ref. Mechanical Parts Grease Lubrication Point Idle Roller Plate 1509 EM-50L Spring Idle Roller 1511 Roller Shaft 1313 EM-50L Pinch Roller 1518 Paper Transportation Drive Roller 1314 EM-50L P6L8 Bushing 1322 Roller Shaft 1313 EM-50L Pinch Roller 1518 Ver.2.0 DEC 2004...
Page 39
DP-2310/3010 DP-2330/3030 Ref. Mechanical Parts Grease Lubrication Point Automatic Duplex Unit Bias Transfer Roller 1221 EM-50L (BTR) KS-660 Registration Pinch 1222 Roller Front Bushing 1231 Rear Bushing 1233 Roller Shaft 1313 EM-50L Pinch Roller 1518 Drive Roller 1409 EM-50L P6L5 Bushing 1150 Pinch Spring 1411...
Tool (FUP) using Ethernet LAN Port and a Crossover Cable. The Network FUP Tool version must be 3.XX or higher, and it can be found on the Panasonic Document Management System CD-ROM included with the main unit or on the CD-ROM included with the PCL or PS/PCL options.
Page 41
DP-2310/3010 DP-2330/3030 (2) For PCL Option The PCL Control Program (2) must be written into the 4 MB onboard, which is assigned as ROM Code (B). The PCL Control Program (3) and PCL Font data (4) are written into the 8 MB in the SLOT 1.
LAN. 1) Install the Network Firmware Update Tool to your PC The option CD-ROM or the Panasonic Document Management System CD-ROM includes the Network Firmware Update Tool and the Main Unit Firmware Code are located in the Option CD-ROM only.
Page 43
If the device is not connected to the LAN, upgrade the firmware code using the USB Port. 1) Install the Local Firmware Update Tool to your PC The option CD-ROM or the Panasonic Document Management System CD-ROM includes the Local Firmware Update Tool and the Main Unit Firmware Code are located in the Option CD-ROM only.
Page 44
4) Upgrading the Main Unit's Firmware Code Start the Local Firmware Update Tool and select the following Firmware Code Parent File Folder in the C:\Panasonic\Panasonic-FUP\Data folder, and select the Firmware Code Type then follow the display instructions to upgrade the Main Unit's Firmware Codes.
Page 45
A. Utilizing the Firmware Update Kit 1) Install the Local Firmware Update Tool to your PC The option CD-ROM or the Panasonic Document Management System CD-ROM includes the Local Firmware Update Tool and the Main Unit Firmware Code are located in the Option CD-ROM only.
Page 46
DP-2310/3010 DP-2330/3030 OFF position. (See 2.7.7.) 2. Insert the Flash Memory Card (4 MB or 8 MB) into the machine. 3. Turn the Main Power Switch on the back and the Power Switch on the left side of the machine to the ON position.
Page 47
DP-2310/3010 DP-2330/3030 2.7.7. Notice after installing the HDD option After the Hard Disc Drive Unit is installed, to prevent a Disc Scan Function from being performed (similar to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below when turing OFF the Power Switches on the machine.
Page 48
DP-2310/3010 DP-2330/3030 2.7.9. Firmware Version DP-2310/3010 DP-SFDL2 A A Vxxxxx (AU) Destination Code (Fax) AU : USA/Canada AB : UK Destination Code (Copier) PU : USA/Canada PB : UK Division Soft (When it is divided into (a) and (b)) Firmware Version (V1xxxx) Language Code A : A-English, C-French &...
Page 49
DP-2310/3010 DP-2330/3030 SFDL2 SPC A A Vxxxxx Firmware Version (V1xxxx) AA: Fixed Model Number DP-2330/3030 SFD L25R A A Vxxxxx (AU) Destination Code (Fax) AU : USA/Canada AB : UK Destination Code (Copier) PU : USA/Canada PB : UK Division Soft (When it is divided into (a) and (b)) Firmware Version (V1xxxx) Language Code...
Page 50
DP-2310/3010 DP-2330/3030 L25R PNL A A Vxxxxx (AU) Destination Code (Fax) AU : USA/Canada AB : UK Destination Code (Copier) PU : USA/Canada PB : UK Division Soft (When it is devided into (a) and (b)) Firmware Version (V1xxxx) Language Code A : A-English, C-French &...
DP-2310/3010 DP-2330/3030 2.8. Adjusting the Printer Registration, LSU Image Side to Side When installing the Paper Tray option, the following LSU Image Side to Side adjustment must be performed. The Printer registration is adjusted at the factory. If copy image is abnormal, specially in the Rotation Copy mode, adjust it by the following procedure. 2.8.1.
Page 52
DP-2310/3010 DP-2330/3030 5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7.
DP-2310/3010 DP-2330/3030 standby. Note: This is the size adjustment and do not worry about the positioning. 2.8.7. ADF Original Read Edge & ADF Main Scan Adjustments 1. Place the Original Document on the ADF. 2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper size.
DP-2310/3010 DP-2330/3030 3 Troubleshooting 3.1. Error Codes (For Copier) The self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier stops. 3.1.1. User Error Codes (U Code) Note: Uxx and a message will appear on the Panel Display. User Error Codes (U Code) Table Code Item...
Page 56
DP-2310/3010 DP-2330/3030 3.1.2. Jam Error Codes (J Code) Section Jam Location Finisher Paper Transport Area Paper entry area 2nd Paper Feed Unit 3rd Paper Feed Unit 4th Paper Feed Unit ADF/i-ADF • J Code Log View Mode The 5 most recent J Codes can be displayed on the Panel Display by pressing "Function" and "3" keys in Standby mode.
Page 57
DP-2310/3010 DP-2330/3030 • Jam Sensor Location of Printer Automatic Duplex Unit Sensor 1 Paper Transport Automatic Duplex Unit Sensor 4 Unit Sensor 2 Paper Transport Dual-Path Unit Sensor 3 Exit Sensor Paper Transport Automatic Duplex Unit Sensor 2 Unit Sensor 3 Exit Sensor Paper Transport Unit Sensor 1...
Page 58
DP-2310/3010 DP-2330/3030 • Jam Sensor Location of Finisher Finisher Exit Sensor Finisher Registration Sensor Stapler • Jam Sensor Location of i-ADF Read Point Sensor Eject Sensor Duplex Eject Sensor • Jam Sensor Location of ADF Original Detection Sensor Read Point Sensor Eject Sensor Ver.2.0...
DP-2310/3010 DP-2330/3030 Jam Error Codes (J Code) Table Code Contents Section The Registration Sensor does not detect paper within a predetermined time after the paper starts feeding. (Sheet Bypass) The Registration Sensor does not detect paper within a predetermined time after the Paper Feed Roller starts rotating.
Page 60
DP-2310/3010 DP-2330/3030 Jam Error Codes (J Code) Table Code Contents Section The Dual-Path Exit Sensor does not detect paper within a predetermined time after the Fuser Unit Paper Exit Sensor is activated. The Paper Transport Unit Sensor 2 does not detect paper within a predetermined B, C time after eject paper Sensor of dual-path exit guide unit is activated.
Page 61
DP-2310/3010 DP-2330/3030 <J70~79, 92, 93 and 94 Codes> DP-2330/ DP-2310/ Contents Section 3030 3010 Read Point Sensor does not detect paper within a predetermined time in the ADF. (Information Code 030 is printed on the Transaction Journal instead.) Read Point Sensor keeps detections paper after a predetermined time in the ADF.
DP-2310/3010 DP-2330/3030 3.1.3. Mechanical Error Codes (E Code) E1: Optical Unit Error Code Function Possible Cause(s) E1- 01 Abnormal Platen Glass 1. Home Position Sensor connector disconnected. Scanning 2. Home Position Sensor defective. 3. Scanner Motor connector disconnected. 4. Scanner Motor defective. 5.
Page 63
DP-2310/3010 DP-2330/3030 E2: Lift DC Motor Error Code Function Possible Cause(s) E2- 01 Lift Motor Rotation 1. Level Sensor connector disconnected. (1st Paper Tray) 2. Level Sensor defective. 3. Lift Mechanism defective. 4. Lift Motor connector disconnected. 5. Lift Motor defective. 6.
Page 64
DP-2310/3010 DP-2330/3030 E3: Development System Error Code Function Possible Cause(s) E3- 01 Toner Bottle Motor Rotation 1. Toner Bottle Motor connector disconnected. 2. Toner Bottle Motor defective. 3. Toner Bottle Motor Drive Mechanism defective. 4. Toner Bottle installed incorrectly. 5. SPC PCB connector disconnected. 6.
Page 65
DP-2310/3010 DP-2330/3030 E4: Fuser Unit Error Code Function Possible Cause(s) E4- 10 Fuser Fan Motor Rotation 1. Fuser Fan connector disconnected. 2. Fuser Fan defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. LVPS defective. E5: System Error Code Function Possible Cause(s)
Page 66
DP-2310/3010 DP-2330/3030 E7: Optional Unit Error (DA-FS300) Code Function Possible Cause(s) E7- 27 Finisher Tray Shift Motor 1. Motor Connector disconnected. 2. Motor defective. 3. Paper Height Sensor Connector disconnected. 4. Paper Height Sensor defective. 5. Gear defective. E7- 59 Finisher Upper Limit 1.
Page 67
DP-2310/3010 DP-2330/3030 3.2. Information Codes Table (For Facsimile) Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) C, D The length of the received document is over 2 m. Read Point Sensor does not Document not set properly. activate within 4 seconds after the Defective Read Point Sensor.
Page 68
DP-2310/3010 DP-2330/3030 Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) Transmitter received FTT after it Line quality poor. (TCF is damaged due transmitted TCF at 2400 bps. to line noise) Received RTN after Receiver defective. (Modem, MJR PCB, communicating at 2400 bps.
Page 69
DP-2310/3010 DP-2330/3030 Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) Receiver transmitted PIN in Line quality poor. (There are excessive response to PRI-Q from errors in received data) transmitter. (Transmitting operator FXB PCB or MJR PCB defective. requests voice contact) T1 timer (35 sec.) elapsed without Wrong number dialed.
Page 70
DP-2310/3010 DP-2330/3030 Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) XMT/ B, C, D CS of modem is not able to turn FXB PCB defective. RCV(V.34) ON during training. Line disconnected. RCV/V.34 Polling is rejected from the remote No polling original set.
Page 71
DP-2310/3010 DP-2330/3030 Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) PSTN Redial count over with no response or busy tone was not detected. Note: U.S.A. and Canadian models will redial only once if a busy tone is not detected. PSTN Power turned Off with applicable Power switched off.
Page 72
DP-2310/3010 DP-2330/3030 Fax Information Codes Code Mode Phase Description of Problem Possible Cause(s) Received an Error or No Remote Internet Fax Errors: Busy or Response from the Remote Job Number Overflow for Relay XMT. Internet Fax. (SMTP Direct XMT) (Retry is possible) Remote Internet Fax Errors: Memory Overflow or No Power.
DP-2310/3010 DP-2330/3030 4 Service Modes 4.1. Service Modes (For Copier) These Service Modes are provided to assist the technician in checking for abnormalities in the copier and a means of making adjustments to the Input/Output of major components. Caution: The factory default parameters are preset (country dependent) for optimum performance and in compliance with the local telecommunication regulations/standards, and do not need to be changed.
Page 74
DP-2310/3010 DP-2330/3030 F5 / F6 Information List (Sample) **********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01 F5-00 Country version USA/CAN F5-50 Auto contrast adjust. F5-01 Frequency desired 60Hz F5-51 Dept. Counter (COPY) F5-02 ..F5-52 Dept. Counter (FAX) F5-03 LSU startup speed Full F5-53 2-sided auto shift...
Page 76
DP-2310/3010 DP-2330/3030 F7 Total Counter List (Sample) **********-F7 TOTAL COUNTER LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01 F7-01 Key Operator ID Code 0000 F7-02 Maintenance Count Total Count PM Count Scanner PM Count ADF Count OPC Drum Count Process Unit Count ADF PM Count Fuser Web Count Developer Count...
Page 77
DP-2310/3010 DP-2330/3030 4.1.3. F4 Mode: Input/Output Status Test Set the machine to service mode and press "4" key on the Keypad. ↓ Press the "START" key. ↓ Enter the number to activate the test then press "START" key. ↓ Press "STOP" key to cancel the test. ↓...
Page 78
DP-2310/3010 DP-2330/3030 F4 Mode (Input Check) Message Display Function Condition Remarks 7 6 5 4 3 2 1 0 004 Fuser Unit Paper Exit Paper is detected. Sensor Dual-Path Exit Guide Unit Unit is connected. Detection Sensor ADU Detection Sensor Unit is connected.
Page 79
DP-2310/3010 DP-2330/3030 F4 Mode (Input Check) Message Display Function Condition Remarks 7 6 5 4 3 2 1 0 007 Paper Transport Unit Unit is connected. Detection Sensor Paper Transport Unit Door Door is open. Sensor Paper Transport Unit Paper is detected. Sensor 4 Paper Transport Unit Paper is detected.
Page 80
DP-2310/3010 DP-2330/3030 F4 Mode (Input Check) Message Display Function Condition Remarks 7 6 5 4 3 2 1 0 010 Registration Sensor Paper is detected. (3rd Paper Tray) JAM Access Cover Open Cover is open. Detection Sensor (3rd Paper Tray) Paper Tray Detection Paper Tray is Sensor...
Page 81
DP-2310/3010 DP-2330/3030 F4 Mode (Input Check) Message Display Function Condition Remarks 7 6 5 4 3 2 1 0 020 Size Sensor C Original detected on the C position. Platen Size Sensor B Original detected on the B position. Size Sensor A Original detected on the Front Side A position.
Page 82
DP-2310/3010 DP-2330/3030 F4 Mode (Input Check) Message Display Function Condition Remarks 7 6 5 4 3 2 1 0 031 ADF Original Sensor Original is detected. ADF Original Width Sensor Original is detected. ADF Original Width Sensor Original is detected. ADF Original Length Original is detected.
Page 83
DP-2310/3010 DP-2330/3030 2. Output Check Press the "START" key to start and press the "STOP" key to reset. F4 Mode (Output Check) Item Function Remark 040 Total Counter When SPC PCB CN715-8 signal level changes to 0V from +24V, count up the Total Counter. 041 Key Counter / Card Counter When SPC PCB CN726-2 signal level changes to 0V from +24V,...
Page 84
DP-2310/3010 DP-2330/3030 F4 Mode (Output Check) Item Function Remark 064 Lift Motor When SPC PCB CN706-2 signal (1st Paper Tray) level changes to 0V from +24V, motor rotates in the ascending direction. 065 OPC Clutch When SPC PCB CN728-2 signal 1 minute level changes to 0V from +24V, clutch operates.
Page 85
DP-2310/3010 DP-2330/3030 F4 Mode (Output Check) Item Function Remark 087 ADU Intermediate Roller Clutch When SPC PCB CN711-2 signal level changes to 0V from +24V, the Clutch operates. 088- Not Used 100 Inner Upper Paper Exit Solenoid When SPC PCB CN719-3 signal level changes to 0V from +24V, the clutch turns OFF.
Page 86
DP-2310/3010 DP-2330/3030 F4 Mode (Output Check) Item Function Remark 163 ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 35% speed. (35% speed rotating) 164 ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 100% speed.
Page 87
DP-2310/3010 DP-2330/3030 4.1.4. F5 Mode: Function Parameters (For Copier) Set the machine to Service Mode and press "5" key on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Touch Panel display. ↓ If you wish to select another code number, scroll the menu with the arrow buttons. ↓...
Page 88
DP-2310/3010 DP-2330/3030 F5 Mode Item Function Default Setting Language Default English English French German Swedish Italian Dutch Portugal Spanish Norway Danish Finnish English Polish Hungary Japanese Czech Russian Greek Chinese Taiwan Korean Batch Printing Mode 0 : Off (From April 2004 MP) 1 : On Fuser Lamp Control 0 : Off...
Page 89
DP-2310/3010 DP-2330/3030 F5 Mode Item Function Default Setting Not Used 0 : No 1 : Auto Finisher 0 : No 1 : Auto System Console 0 : No 1 : Auto Paper Transport Unit 0 : No 1 : Auto Not Used Digital QUANTUM 0 : Off...
Page 90
DP-2310/3010 DP-2330/3030 F5 Mode Item Function Default Setting Insert Paper Count 0 : No 1 : Yes Dept Code Reentry Again 0 : No 1 : Yes Not Used TH Sensor (DEV) 0 : No 1 : Mid 2 : Large Not Used Auto Contrast Adjust 0 : No...
Page 92
DP-2310/3010 DP-2330/3030 F5 Mode Item Function Default Setting B4/FLS Size Selection 0 : B4 1 : 8 x 13 2 : 8.5 x 13 Manual Skyshot Mode 0 : Off 1 : M1, On 2 : M2, On 3 : M1, M2, On Digital Skyshot Mode 0 : No 1 : Normal...
Page 93
DP-2310/3010 DP-2330/3030 F5 Mode Item Function Default Setting Bypass Detection 0 : Japan 1 (for USA / Canada) (Factory use only) 1 : USA/CAN 2 (for Europe) 2 : Europe 3 : Other Bp tray B4/FLS/LGL (FA) 0 : B4 3 (for USA / Canada) (Factory use only) 1 : 8 x 13...
Page 94
DP-2310/3010 DP-2330/3030 4.1.5. F6 Mode: Adjust Parameters (For Copier) Set the machine to Service Mode and press "6" key on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Touch Panel display. ↓ If you wish to select another code number, scroll the menu with the arrow buttons. ↓...
Page 95
DP-2310/3010 DP-2330/3030 F6 Mode Setting Item Remarks Range Not Used Side Adjust (ADU) Adjustment of LSU side-side (ADU). -8 - +7 0.5mm Charge Roller Voltage Charge voltage compensation adjustment. -76 - +76 2.60V Standard Laser Power Laser power compensation adjustment. -29 - +25 Std Bias DC Voltage Adjustment of bias standard voltage.
Page 96
DP-2310/3010 DP-2330/3030 F6 Mode Setting Item Remarks Range Transfer Current Side 2 Adjustment of Transfer Current. -16 - +15 0.6uA Not Used T Mode Image Density Image density adjustment for Text mode. -99 - +99 (-) : Darker. (+) : Lighter. T/P Mode Image Density Image density adjustment for Text/ Photo -99 - +99...
Page 97
DP-2310/3010 DP-2330/3030 F6 Mode Setting Item Remarks Range QUANTUM Halftone Read Value of QUANTUM Laser duty of Check +127 - +255 pattern. (Read Only) QUANTUM Black Read Value of QUANTUM Laser duty of Black +127 - +255 pattern. (Read Only) Temperature Sensor Value Value of Temperature sensor.
Page 98
DP-2310/3010 DP-2330/3030 4.1.6. F7 Mode: Electronic Counter Set the machine to Service Mode and press "7" key on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Touch Panel display. ↓ If you wish to select another code number, scroll the menu with the arrow buttons. ↓...
Page 99
DP-2310/3010 DP-2330/3030 F7 Mode Service Item Remarks Mode Electronic 03 Paper Feed 00 Sheet Bypass Count Total count of paper fed from the sheet Counters Count bypass. 01 1st Paper Tray Count Total count of paper fed from the 1st paper tray.
Page 100
DP-2310/3010 DP-2330/3030 4.1.7. F8 Mode: Service Adjustment Set the machine to Service Mode and press "8" key on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Touch Panel display. ↓ If you wish to select another code number, scroll the menu with the arrow buttons. ↓...
Page 101
DP-2310/3010 DP-2330/3030 F8 Mode Item Remarks Move Mirror To Lock a) Press the Start key to move the mirror unit to the locked position for transporting the copier. b) When the mirror unit is locked, the machine will not accept any numerical key input. Note: The locking operation is automatically reset when the Power switch is turned ON again.
Page 102
DP-2310/3010 DP-2330/3030 4.1.8. F9 Mode: Unit Maintenance Set the machine to Service Mode and press "9" key on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Touch Panel display. ↓ If you wish to select another code number, scroll the menu with the arrow buttons. ↓...
Page 103
DP-2310/3010 DP-2330/3030 F9 Mode Service Item Remarks Mode Unit 06 RAM 00 Parameter Initialize Resets the Fax and Function Maintenance Initialize parameters to default values. Note: Turn the Power Switch to the OFF and back to the ON position to enable the parameter settings.
DP-2310/3010 DP-2330/3030 4.2. Service Modes (For Facsimile) Caution: The factory default parameters are preset (country dependent) for optimum performance and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of these parameters may cause the unit to be no longer compliant or become inoperable.
Page 105
DP-2310/3010 DP-2330/3030 4.2.3. Fax Service Mode 1 (Function Parameter Setting) Use the following procedure to change the function parameters. Select the "01 Function Param. Setting" on the Touch Panel display. ↓ Select the desired code number on the Touch Panel display. ↓...
Page 106
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 005 Destination 000 : Austria Sets the Destination Code after installing the Fax Code 001 : U.K. Communication Board (DA-FG300). 002 : Canada 003 : Denmark Note: 004 : Taiwan It is not necessary to set the parameter for the 005 : Finland following suffix (Destinations).
Page 107
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 012 DTMF Level 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1 dBm steps. 15 = -15 dBm 013 G3 RX EQL 1 = 0dB Selects the cable equalizer for G3 reception mode, 2 = 4dB 0dB, 4dB, 8dB or 12dB.
Page 108
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 026 Non-Standard 1 = Off (Invalid) Selects own mode (Panafax mode). 2 = On (Valid) 027 Short Protocol B 1 = Off (Invalid) Selects the short protocol mode. 2 = On (Valid) 028 Short Protocol D 1 = Off (Invalid) Selects the short protocol mode.
Page 109
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 046 On-Hook Time 0 = 0 sec. Selects the on-hook time between sequential communication calls in 1 second step intervals. 90 = 90 sec. 047 Response Wait 1 = 1 sec. Selects the waiting interval for the response after Interval completing the dialing.
Page 110
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 068 NYSE Fax 1 = Off Selects whether the machine will forward the Forward 2 = On incoming and outgoing faxes to a specified station. (USA and Note: Once this parameter is activated, Fax Forwarding Canada Only) via Fax Parameter 054 is automatically disabled, an Access Code of "0000"...
Page 111
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function 083 Not Used 084 Line As No 1 = Ring (ring) Selects whether to ring or send a busy tone to the Paper 2 = Busy (keep line busy) remote station when the recording paper runs out or the unit cannot receive because of any trouble.
Page 112
DP-2310/3010 DP-2330/3030 Function Parameter Table Parameter Selections Function Not Used 122 LDAP 1 = Off When LDAP is used, specialize characters may be 2 = On displayed as different characters. Not Used 175 FAX/EMAIL 0 = Address Book Selects the FAX/EMAIL Default. Default 1 = Mode Set Not Used...
Page 113
DP-2310/3010 DP-2330/3030 4.2.4. Fax Service Mode 3 (Printout of Lists, Reports and Test Results) From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace and the Toner Order Form. 4.2.4.1.
Page 115
197 ---------- 148 ---------- 198 ---------- 149 ---------- 199 ---------- -PANASONIC ***** DP-3030 ****************** - - ****** -12345678901234567890- *********** Note: 1. The contents of the Function Parameter List may vary depending on the country’s regulations. 2. “ * ” mark will be shown on the left side of number when setting was changed from default.
Page 117
Press "FUNCTION" and "C (CLEAR)" keys simultaneously to exit the service mode. **************-PRINTER REPORT-********************* DATE MMM-dd-yyyy ***** TIME 19:02******** LAST PRINT ERROR : MMM-dd-yyyy 15:38 J00 00-00000016 CUSTOMER ID : 1234567890123456 FIRMWARE VERSION : DP-3010 AAV12900AU : AAV20100 : 30cpm V20100 TRANSMIT COUNTER : 000475 RECEIVE COUNTER : 000398 COPY COUNTER...
Page 118
DP-2310/3010 DP-2330/3030 4.2.4.4. All Document Files Print the document files from the Flash Memory. Select the "03 Print Param. List/Report" on the Touch Panel display. ↓ Select the "05 All Document Files" on the Touch Panel display. ↓ Touch the "OK" button 3 times. ↓...
Page 120
DP-2310/3010 DP-2330/3030 4.2.4.6. Toner Order Form The Toner Order Form can be printed out manually by the following procedure. Select the "03 Print Param. List/Report" on the Touch Panel display. ↓ Select the "07 Toner Order Form" on the Touch Panel display. ↓...
Page 121
< ************************************* **** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer Panasonic Corp. (2) by Phone: 1 201 111 5555 (3) by Fax: 1 201 111 4444 (4) Thank you for your order.
Page 122
DP-2310/3010 DP-2330/3030 4.2.5. Fax Service Mode 4 (Modem Test) 4.2.5.1. Binary Signal This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Select the "04 MODEM Tests" on the Touch Panel display. ↓...
Page 123
DP-2310/3010 DP-2330/3030 4.2.5.2. Tonal Signal This Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Select the "04 MODEM Tests" on the Touch Panel display. ↓ Select the "02 Tonal Signal" on the Touch Panel display. ↓...
Page 124
DP-2310/3010 DP-2330/3030 4.2.5.3. DTMF Signal This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output. The DTMF signal can be generated using the following procedure. • DTMF Single Tone Select the "04 MODEM Tests" on the Touch Panel display. ↓...
Page 125
DP-2310/3010 DP-2330/3030 4.2.5.4. Binary Signal (V.34) This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (V.34) Select the "04 MODEM Tests" on the Touch Panel display. ↓ Select the "05 V34 MODEM"...
Page 126
DP-2310/3010 DP-2330/3030 4.2.6. Fax Service Mode 6 (RAM Initialization) Initializes RAM and restores the Function Parameters to their default values. Note: This operation should be performed when the unit is first installed. Select the "06 RAM initialize" on the Touch Panel display. ↓...
DP-2310/3010 DP-2330/3030 4.2.7. FAX Service Mode 8 (Check & Call) 4.2.7.1. Overview This feature enables the Authorized Servicing Dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner.
Page 128
DP-2310/3010 DP-2330/3030 Error Remarks Code Report Ex-xx Refer to the Mechanical Error Code (E Code) Table. (Sect. 3.1.3.) Out of Toner. Refer to the Jam Error Code (J Code) Table. (Sect. 3.1.2.) (J93 is not Logged for DP-2330/3030) Refer to the User Error Code (U Code) Table. (Sect. 3.1.1.) Low Toner.
Page 129
ERROR CODE ERROR COUNT ------------------------------------------------------------------------------------------- MMM-dd-yyyy 20:07 E04-01 00-00000013 | MMM-dd-yyyy 20:04 E04-01 00-00000013 | ------------------------------------------------------------------------------------------- -LOGO PANASONIC ***** DP-3030 *********************** -CHARACTER ID - ***** -31415926535897932384-********* Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Print Error...
Page 130
TRANSMIT COUNTER : 000244 RECEIVE COUNTER : 000082 COPY COUNTER : 000000 PRINT COUNTER : 000000 -LOGO PANASONIC ************************************ -CHARACTER ID - ***** -31415926535897932384-*********** Explanation of Contents (1) Low Toner Message (Fixed) “MACHINE IS RUNNING OUT OF TONER” (2) Customer ID...
Page 131
< ************************************* **** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer Panasonic Corp. (2) by Phone: 1 201 111 5555 (3) by Fax: 1 201 111 4444 (4) Thank you for your order.
Page 132
ERROR CODE ERROR COUNT ------------------------------------------------------------------------------------------- MMM-dd-yyyy 20:07 E04-01 00-00000013 | MMM-dd-yyyy 20:04 E04-01 00-00000013 | ------------------------------------------------------------------------------------------- -LOGO PANASONIC ***** DP-3030 *********************** -CHARACTER ID - ***** -31415926535897932384-********* Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Call Counter Pre-Set Value...
Page 133
DP-2310/3010 DP-2330/3030 4.2.8. Service Mode 9 (System Maintenance) 4.2.8.1. Overview This Service Mode is used to maintain the machine. Use the following procedure for System Maintenance. Select the "09 System Maintenance" on the Touch Panel display. ↓ Select the "01 Send RCV’D File". The display changes to the Fax Mode. ↓...
Page 134
DP-2310/3010 DP-2330/3030 memo Ver.2.0 DEC 2004...
DP-2310/3010 DP-2330/3030 5.21. Packing and Accesories 5.21.1. Packing and Accesories (For PU and DP-3010-PA; with i-ADF Preinstalled) Ver.2.0 DEC 2004...
Page 215
DP-2310/3010 DP-2330/3030 Ver. 2.0 DEC 2004...
Page 216
DP-2310/3010 DP-2330/3030 Ver.2.0 DEC 2004...
Page 217
DP-2310/3010 DP-2330/3030 Ver. 2.0 DEC 2004...
Page 218
DP-2310/3010 DP-2330/3030 5.21.2. Packing and Accesories (For Other Destinations) Ver.2.0 DEC 2004...
Page 219
DP-2310/3010 DP-2330/3030 Ver. 2.0 DEC 2004...
Page 220
DP-2310/3010 DP-2330/3030 Ver.2.0 DEC 2004...
Page 221
DP-2310/3010 DP-2330/3030 Ver. 2.0 DEC 2004...
DP-2310/3010 DP-2330/3030 6 Alphanumerical Parts List Alphanumerical Parts List Part Number Part Name Ref. No. Destination 023120FZWS Screw 2943 030060FZTP Screw 2942 030060FZWS Screw 2736 040040FNBI Screw 3030 040060FNBI Screw 2633 55SPM25D7ND1 Motor, Transport 1320 AM59259-A Micro Switch B3X6TTS-RP Screw (For DP-2310/3010 only) CR2032 Battery DA-AR250-PB...
Page 275
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZEC102441 AU, YY AA, AB, AG, AH, AJ, AL, DZEC102447 PC Board, MJR (For DP-2310/3010) 1915 AM, AP, AR, AV, EE, EN, YG, YX DZEC102518 Other DZEC102722 PC Board, FXB (For DP-2310/3010) 1916 Except PU DZEC102748...
Page 283
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZHP010680 Control Panel Unit (For DP-3030) DZHP010682 Control Panel Unit (For DP-2330) DZHP010687 Assembly, Switch (For DP-2330/3030) DZHP008297 Assembly, Hopper (For DP-2330/3030) DZHP011286 CD (For DP-2330/3030) 2114 DZHP011380 Inverting ADF Unit (For DP-2330/3030) 1668 DZHP011455...
Page 284
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJA000719 Bracket, Motor 1312 DZJA000721 Bracket S, B2 Sensor 3204 Except PU DZJA000722 Guide, Feed 2 Roller 3206 Except PU DZJA000723 Bracket 2324 DZJA000724 Hinge, Arm 1622 DZJA000725 Base, Left Hinge (A) 1664 DZJA000726...
Page 285
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJA001351 Bracket, EMI DZJA001354 Bracket, Choke Coil 3 Except PU DZJA001495 Stay, Duplex 1259 DZJA001496 Bracket, Duplex 1260 DZJB000130 Base, Front Lamp DZJB000131 Base, Rear Lamp DZJB000132 Base, Mirror 2 DZJB000134 Frame, Scanner Base DZJB000135...
Page 287
Part Name Ref. No. Destination DZJE001129 Cover, LCD Panel (For DP-2310/3010) Cover, Upper Control Panel DZJE001130 Except PU (For DP-3010) Cover, Upper Control Panel DZJE001131 Except PU (For DP-2310) DZJE001132 Cover, LCD Panel (For DP-2310/3010) DZJE001133 Except PH, PK, PT...
Page 288
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJF000679 Guide, Tray 1293 DZJF000680 Guide, Reverse Roller 1294 DZJF000681 Plate, Pressure 1295 DZJH000083 Washer DZJH000084 Support, Locking DZJH000118 Sheet, Feed 1281 DZJH000120 Sheet, Pad 1282 Except PU, PH, PK, PT DZJH000135 Polyslider 1288...
Page 289
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJL000366 Bracket, Roof DZJL000369 Plate, Slide DZJL000373 Plate Nut 1106 DZJL000374 Plate, Handle DZJL000375 Plate, RF Frame DZJL000376 Terminal, Fuser Lamp 1050 DZJL000377 Plate, High Voltage 1228 DZJL000380 Plate, Heat Sink 1 1886 DZJM000159...
Page 290
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJM000470 Stopper, Tray 1254 DZJM000473 Holder, Paper 1524 DZJM000474 Sheet, Protection 1161 DZJM000475 Slider 1665 DZJM000476 Sponge 1880 DZJM000477 Stopper, Rubber 1783 DZJM000479 Film, Guide 1867 DZJM000483 Seal, Reflection DZJM000486 Seal, White 1630...
Page 291
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZJM001259 Seal 4, Supply Mouth DZJM001260 Sheet, Handle Cover DZJM001261 Finger, Upper 1067 DZJM001264 Film, Shading DZJM001267 Sheet, Cover DZJM001270 Sponge (For DP-2310/3010) 1280 DZJM001273 Sponge, Hopper DZJM001274 Sheet, Strap Cover 1092 DZJM001275...
Page 292
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZKG000123 Shaft, P8S 1705 DZKG000124 Shaft, P6 1624 DZKG000137 Assembly, Drive Shaft DZKG000351 Shaft, Pinch 1068 DZKG000356 Shaft, Feed Roller 1245 DZKG000357 Pin, Fulcrum 1215 DZKG000358 Shaft, Clutch DZKG000359 Pin, Idle Gear DZKG000360...
Page 293
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZKN000201 Spring, Handle 1315 DZKN000202 Spring, Actuator 1316 DZKN000203 Spring, Hinge (Silver, i-ADF) 1786 DZKN000204 Spring, Hinge (Black, ADF) 3207 Except PU DZKN000205 Coil Spring, OP DZKN000206 Spacer, Gear DZKN000207 Coil Spring, Ground 1632...
Page 294
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZKP000254 Lever, Web Stopper 1082 DZKP000327 Spring Idle Roller 1020 DZKP000352 Plate, Charge DZKP000358 Plate Spring, Pinch Roller 1671 Except PU DZKQ000012 Spring, Actuator 1607 DZKQ000028 Spring, C 1148 DZKQ000030 Spring, B...
Page 295
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZLA000338 Roller, Magnet DZLA000340 Roller, Drive 1409 DZLA000341 Roller 2, Drive 1410 DZLA000342 Roller, Intermediate 2306 DZLA000344 Pinch Roller 1059 DZLA000347 Roller, Exit 1028 DZLA000348 Roller, Web Pressure 1080 DZLA000349 Roller, Cleaning...
Page 296
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZLF000342 Gear, E20 DZLF000344 Gear, E42B21 DZLF000345 Gear, E23 DZLF000347 Gear, B39 DZLF000349 Gear, B42B21 DZLF000350 Gear, B40 DZLF000351 Gear, B22 DZLF000352 Gear, B32 DZLF000354 Gear, E25 DZLF000355 Gear, E29 DZLF000356 Gear, E41 Free...
Page 297
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZLF000678 Gear, E18 1332 DZLF000679 Gear, E25 1505 DZLG000009 Clutch, Reverse 1132 DZLK000011 Belt, Inner Timing DZLK000012 Belt, Outer Timing DZLK000013 Belt, Timing 1814 DZLK000014 Belt, STS 1318 DZLK000021 Belt, Synchro DZLL000004...
Page 298
Cover, RR Handle DZMA004243 Cover, Rear Blind DZMA004245 Cover, Right Rear DZMA004249 Cover, Rear DZMA004268 Cover, Front (For DP-2310) DZMA004272 Cover, Front (For DP-3010) DZMA004322 Holder, Battery (For DP-2310/3010) DZMA004338 Original Guide, Front 1606 DZMA004339 Original Guide, Rear 1605 DZMA004358...
Page 299
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZMG000015 Magnet 2308 DZMG000018 Latch 1833 DZMH000010 Bracket, Front 2316 DZMH000011 Bracket, Rear 2317 DZMH000012 Bracket, Solenoid 1508 DZMH000013 Hinge, Platen Except PU DZMH000015 Bracket, Cover 1325 DZMK000005 Lever, Release 1211 DZML000335...
Page 301
Carton Box 3401 DZRB000733 Carton Box 3701 DZRB000750 Assembly, HDD Cushion 3801 Carton Box (For Product Made in Japan) DZRB000862 2103 PU, PA (For DP-3010) DZRB000863 Carton, Top 2101 DZRB000864 Carton, Bottom 2107 DZRB000865 Pad, Top 2102 DZRB000866 Carton Bar...
Page 302
Carton Box (For Product Made in Japan) Except PU, PK (For DP-2310) DZRB000906 Carton Box (For Product Made in DZRB000942 Philippines) (For DP-3010) Carton Box (For Product Made in DZRB000948 Philippines) (For DP-2310) 2103 Carton Box (For Product Made in...
Page 303
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination DZSM000689 Installation Instructions 4104 Installation Instructions DZSM000691 3702 (For DP-2310/3010) Installation Instruction DZSM000692 3404 (For DA-PC300) DZSM000696 Installation Instruction 3802 Installation Instructions DZSM000717 2116 (For DP-2310/3010) DZSM000754 Installation Instruction 3501 DZSM000756 Installation Instruction...
Page 304
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination FFPKE10251 Box, Lift 1162 FFPKE10261 Cover, Box 1163 FFPLP0976 Spring, Reset 1170 FFPMF10271 Gear 1 1164 FFPMF10281 Gear 2 1165 FFPMF1029 Gear 3 1166 FFPMF1030 Gear 4 1167 FFPMF1031 Gear, Worm (For DP-2310/3010) 1169...
Page 305
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination PF4102K178 Frame, Front Base 3013 PF4102K211 Harness, SW 2944 PF4102K212 Harness, Top Cover Sensor 2851 PF4102K213 Harness, Paper Exit Sensor 2933 PF4102K215 Harness, Tray 2508 PF4102K221 Motor, Set 2931 PF4102K222 Solenoid, Paper Detection...
Page 306
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination PF4102P265 Guide2, Paper 2909 PF4102P266 Guide1, Paper 2907 PF4102P269 Holder, Feed Arm 2918 PF4102P270 Roller, Feed Arm 2916 PF4102P272 Arm, Rear 2610 PF4102P274 Holder, Belt Tension 2704 PF4102P275 Roller2, Paper Hold 2841 PF4102P276...
Page 307
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination PF4102P391 Cushion, Lever 2620 PF4102P398 Sheet, Mylar 2922 PF4102P405 Tray, Staple Guide 2920 PF4102P406 Guide, Paper 2921 PF4102P512 Motor, Tray Elevation 2511 PF4102P513 Solenoid, Paddle 2728 PF4104K141 Assembly, Paper Hold Lever 2844 PF4104K143 Assembly, Exit Guide...
Page 308
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination PF4124P009 Shaft, Lock Lever 3020 PF4124P010 Bracket, PCB 3007 PF4124P011 Cover, Right 2604 PF4124P012 Guide, Rail 3006 PF4124P013 Cover, Front 2602 PF4124P014 Lever, Front 2603 PF4124P015 Cover, Rear 2606 PF4124P016 Cover, Staple...
Page 309
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination XTB3+4F Screw (For DP-2310/3010 only) XTB3+4FFJ Screw XTB3+6F Screw (For DP-2310/3010 only) XTB3+6FFJ Screw XTB3+6FFJ-RP Screw XTB3+6J Screw (For DP-2310/3010 only) XTB3+6JFJ Screw XTB3+8F Screw (For DP-2310/3010 only) XTB3+8FFJ Screw XTB3+8G...
Page 310
DP-2310/3010 DP-2330/3030 Alphanumerical Parts List Part Number Part Name Ref. No. Destination XYN3+J8 Screw (For DP-2310/3010 only) XYN3+J8FJ Screw XYN4+F8 Screw (For DP-2310/3010 only) XYN4+F8FJ Screw Ver.2.0 DEC 2004...
Page 311
DP-2310/3010 DP-2330/3030 memo Ver. 2.0 DEC 2004...