Microscan MS-7180 Manuals

Manuals and User Guides for Microscan MS-7180. We have 1 Microscan MS-7180 manual available for free PDF download: User Manual

Microscan MS-7180 User Manual (138 pages)

Industrial Scanner

Brand: Microscan | Category: Scanner | Size: 1 MB

Table of Contents
3
List of Illustrations
5
List of Tables
6
About this Manual
6
Keystroke Entries
7
Approvals
7
Warning and Caution Summary
7
Safety Labels
7
Chapter 1 Setup and Installation

12
Chapter 2 Menu Configuration

32
- Entering the Menu Configuration Program
  32
- Using the Menu Configuration Program
  32
- Figure 2-1 Configuration Program - Main Menu
  32
- Saving Menu Changes
  34
- Loss of Communications
  34
- Defining Special Characters
  34
- Communications Menu
  35
  - Figure 2-2 Communications Menu Structure
    35
  - Response Timeout
    39
  - Baud Rate
    40
  - Intercharacter Delay
    40
  - Stop Bits
    40
- Operations Menu
  42
  - Figure 2-3 Operations Menu Structure
    42
  - End of Read Cycle
    44
  - Figure 2-4 External Level Trigger Signals
    44
  - Figure 2-5 External Edge Trigger Signals
    44
  - External Trigger Polarity
    46
  - Noread Message
    47
  - Field Separator
    48
  - Good Decode Reads
    48
  - Sequential Matching
    50
  - Match Length
    51
- Code Types Menu
  52
  - Figure 2-6 Code Types Menu Structure
    52
  - Narrow Margins
    53
  - Table 2-1 Symbology Identifier Option Values
    53
  - Check Digit
    54
  - Code Length
    54
  - Interleaved 2 of 5
    56
  - Code 128
    58
- User Outputs Menu
  61
  - Figure 2-7 User Outputs Menu Structure
    61
  - Beeper Volume
    62
  - New Master Pin
    64
  - Partial Output
    66
- Raster Setup Menu
  67
- Figure 2-8 Raster Setup Menu Structure
  67
- Figure 2-9 Raster Sweep Arc
  67
- Table 2-2 Raster Settings
  67
Chapter 3 Serial Configuration

70
Chapter 4 Calibration

88
- About Calibration
  88
- Autocalibration
  88
- By Serial Command
  88
- By Menu Command
  89
- Other Menu Parameters
  91
- Figure 4-1 Calibration Setup Menu
  91
- Recalling Factory Settings
  92
- Saving Current Settings
  92
- Motor Speed
  92
- Gain
  93
- Tracking
  94
- Bandwidth
  94
- Clock Speed
  94
- Bar Size Measurements
  95
- Scan Rate
  95
Chapter 5 Operational Commands

98
- Summary of Operational Commands
  98
- Table 5-1 Operational Commands
  98
- Program Management Commands
  99
- Device Control Commands
  99
- Code Type Commands
  100
- Counter Commands
  100
- Test Commands
  101
- Status Commands
  101
- Master Label Commands
  101
- Appendices
  103
- Appendix A - Scanner Specifications
  
  104
  - Scanner Specifications
    105
- Appendix B - ASCII Table
  
  107
  - Table A-1 ASCII Table with Control Characters
    107
- Appendix C - Orientation
  
  108
  - Figure A-3 Ladder Orientation
    108
  - Figure A-4 Picket Fence Orientation
    108
  - Label Orientation
    108
  - Figure A-5 Angled Picket Fence Orientation
    109
  - Figure A-6 Detector Side Orientation
    109
  - Figure A-7 Detector Right-Angle Orientation
    110
  - Figure A-8 Label Dimension
    110
  - Figure A-9 Raster Image
    110
- Appendix D - Ground and Shield Considerations
  
  111
  - Figure A-10 Grounding Diagram, Scanner-Host
    111
  - Ground Loops
    111
- Appendix E - Defaulting the Scanner
  
  112
  - Figure A-11 Host Connector Default Pins
    112
- Appendix F - Troubleshooting
  
  113
  - Table A-2 Troubleshooting
    113
- Appendix G - Bar Code Symbology
  
  116
- Appendix H - Interface Standards
  
  117
- Appendix I - Auxiliary Monitor
  
  118
  - Full Duplex Mode
    121
  - Daisy Chain Mode
    122
- Appendix J - Multidrop Communications
  
  123
- Appendix K - Glossary of Terms
  
  127
  - Figure 1-9 Power Connector
    136

Microscan Categories

Barcode Reader

Scanner

Digital Camera Laboratory Equipment Card Reader

More Microscan Manuals

Microscan MS-7180 Manuals

Microscan MS-7180 User Manual (138 pages)

Table of Contents

Chapter 1 Setup and Installation

Chapter 2 Menu Configuration

Chapter 3 Serial Configuration

Chapter 4 Calibration

Chapter 5 Operational Commands

Appendix A - Scanner Specifications

Appendix B - ASCII Table

Appendix C - Orientation

Appendix D - Ground and Shield Considerations

Appendix E - Defaulting the Scanner

Appendix F - Troubleshooting

Appendix G - Bar Code Symbology

Appendix H - Interface Standards

Appendix I - Auxiliary Monitor

Appendix J - Multidrop Communications

Appendix K - Glossary of Terms

Related Products

Microscan Categories