User Manuals: Barco Cine 7 R9002381 Projection System

Manuals and User Guides for Barco Cine 7 R9002381 Projection System. We have 1 Barco Cine 7 R9002381 Projection System manual available for free PDF download: Owner's Manual

Barco Cine 7 R9002381 Owner's Manual

Barco Cine 7 R9002381 Owner's Manual (82 pages)

BARCO Projection systems Ciné

Brand: Barco | Category: Projector | Size: 1 MB

Table of Contents

Table of Contents
3
Table of Contents

4
Safety Instructions

9
- Installation INSTRUCTIONS
  13
Connections

13
Getting Started

21
- Remote Control & Local Keypad
  21
- Battery Installation in the RCU
  21
- How to Replace the Batteries in the RCU
  21
- Gaining Access to the Local Keypad
  22
- Overview of Functions
  22
- Operating the Projector
  23
- Switching on
  23
- Start up in Operational Mode
  24
- Start up in Stand by Mode
  24
- Warning
  24
- RCU Commands to the Projector
  24
- Pointing the RCU to the Reflective Screen
  24
- Pointing the RCU Directly to the IR Sensors
  25
- Hardwired Remote Input
  25
- Projector Address
  25
- Why a Projector Address
  25
- Set up an Individual Projector Address
  25
- How to Control the Projector or Projectors
  25
- Before Using the RCU
  26
- Common Address
  26
- Display the Projector Address on the Screen
  26
- How to Program an Address into the RCU
  26
- Controling the Projector
  26
- Input Selection Modes
  26
- When the Source Is Selected
  27
- Picture Controls
  27
- The Pause Key
  28
- The Freeze Key (Only with Line Doubler)
  28
Start up of the Adjustment Mode

29
- Adjustment Mode
  29
- Start up
  29
- Possible Paths
  30
Main Menu

31
- Overview Flowchart
  31
- Image Control
  32
- Starting up
  32
- Line Doubler (if Available)
  32
- Why Line Doubling
  32
- How to Enable/Disable the Line Doubler
  32
- Line Multiplier (if Available)
  32
- Why Line Multiplying
  32
- How to Change the Multiplier Setting
  33
- Line Multiplier ON/OFF
  33
- Multiplier Mode
  33
- What Can be Selected Within the Multiplier Mode
  33
- How to Start up the Multiplier Mode Menu
  33
- How to Change the Scan Rate
  34
- Motion Processing
  34
- Why Motion Processing
  34
- How to Activate
  34
- Video Equalizing
  34
- What Can be Done
  34
- How to Select Video Equalizing
  34
- How to Adjust the Video Equalizing
  35
- Noise Reduction
  35
- What Can be Done
  35
- How to Select and Adjust the Noise Reduction
  35
- Contrast Enhancement
  35
- How to Select and Adjust the Contrast Enhancement
  35
- Color Adjust
  36
- What Can be Done
  36
- How to Select 'Color Adjust' and to Select a New Color Temperature
  36
- Format Select
  36
- How to Select a 'Format
  36
- How to Add a Name to a 'Format
  37
- How to Store the Settings to a New 'Format
  37
- IRIS Control
  37
- Start up
  37
- Note
  37
- IRIS Touch up
  37
- What Can be Done
  37
- How to Start up the IRIS Touch up
  38
- IRIS Auto Converge
  38
- What Can be Done
  38
- How to Start up the IRIS Auto Converge
  38
- IRIS Full Alignment
  38
- How to Start up the IRIS Full Alignment
  38
- Sound Control
  39
- What Can be Done
  39
- How to Start up and to Select the Sound Control
  39
- Function Keys
  39
- How to Get an Overview of the Programmed Keys
  39
- Service Menus
  39
- How to Enter the Service Menu
  40
Entering the Service Menus

41
- Service Menus
  41
- What Is Available in the Service Menus
  41
- How to Enter the Service Menus
  41
- Password Protection
  42
- Entering the Password
  42
Random Access Adjustment Mode

43
- Starting up
  43
- Overview Flowchart
  43
- Selecting Setup Pattern
  44
- Set up of the Selected Setup Pattern
  44
- Note
  44
- Internal Cross Hatch Pattern
  44
- When Using the Internal Cross Hatch Pattern
  44
- Factory Preset Frequencies
  44
- Random Access Adjustment Mode Selection Menu
  45
- What Is Possible
  45
- Picture Tuning
  45
- Start up the Picture Tuning
  45
- Color Balance
  45
- What Can be Done
  45
- How to Select the Color Balance
  46
- Fixed Color Balance
  46
- Custom Color Balance
  46
- Sync Fast/Slow Adjustment (Only Inputs 3,4,5,6)
  47
- What Can be Done
  47
- How to Setup the Sync Function
  47
- Note
  47
- Decoding
  47
- How to Set up
  47
- Port 2 : Video or S-Video
  47
- How to Configure Port 2
  47
- Switching Peaking ON/OFF
  48
- Line Doubler/Line Multiplier
  48
- What Can be Done
  48
- Switching the Multiplier ON/OFF
  48
- Motion Processing
  49
- Why Motion Processing
  49
- How to Activate
  49
- Output Mode
  49
- What Can be Done
  49
- How to Select a New Scan Rate
  49
- Video Equalizing
  50
- What Can be Done
  50
- How to Select Video Equalizing
  50
- How to Adjust the Video Equalizing
  50
- Noise Reduction
  50
- Contrast Enhancement
  51
- What Can be Done
  51
- How to Select and Adjust the Contrast Enhancement
  51
- Advanced Settings
  51
- How to Select the Advanced Settings
  51
- Why Time Base Correction
  51
- How to Activate
  51
- Clamp Gating
  52
- Luminace Delay
  52
- Vertical Sync Reference
  52
- Factory Preset
  53
- Geometry Adjustments
  53
- What Can be Done
  53
- Start up
  53
- Important
  53
- Horizontal Phase Adjustment
  54
- Start up
  54
- Note
  54
- How to Adjust
  54
- Raster Shift Adjustment
  54
- What Has to be Done
  54
- Caution
  54
- Note
  55
- Warning
  55
- Left-Right (East-West) Adjustments
  55
- What Can be Adjusted
  55
- Start up
  55
- Which Adjustment Can be Executed ?
  55
- How to Enter an Alignment
  56
- Seagull Correction
  57
- Top-Bottom (North-South) Adjustments
  57
- What Can be Adjusted
  57
- Start up
  57
- Note
  57
- Which Adjustment Can be Executed
  57
- How to Enter an Alignment
  58
- Seagull Correction
  58
- Size Adjustment
  59
- What Can be Done
  59
- Start up
  59
- Hint
  59
- Blanking Adjustments
  60
  - What Can be Done
    60
  - Start up
    60
  - Vertical Linearity Adjustment
    60
  - How to Adjust the Blanking
    61
  - Convergence Adjustment
    62
  - What Has to be Done
    62
  - Note
    62
  - Adjustment Order
    62
  - Start up
    62
  - How to Adjust
    62
Service Mode

63
- Start up
  63
- Overview Flowchart
  63
- Projector Set-Up
  64
- What Can be Done
  64
- Start up the Projector Set-Up
  64
- Identification
  64
- What Can be Seen
  64
- How to Start up
  65
- Total Run Time
  65
- What Can be Displayed
  65
- Note
  65
- Change Password
  65
- What Can be Done
  65
- How to Select
  66
- How to Enter a New Password
  66
- Change Language
  66
- What Can be Done
  66
- How to Change the Language
  66
- Change Projector Address
  66
- How to Change that Address
  67
- Change Baudrate
  67
- What Can be Set up
  67
- How to Set up
  67
- Power up Mode
  67
- What Can be Done
  67
- How to Change the Mode
  68
- Commonn Address
  68
- What Can be Done
  68
- Barco_Logo
  68
- Warning
  68
- How to Add the BARCO Logo
  68
- Memory Management
  69
- What Can be Done
  69
- How to Select
  69
- Copy a Block
  69
- How to Copy
  70
- Deletion of Blocks
  70
- What Can be Done
  70
- Deleting Block by Block
  70
- How to Delete a Block
  70
- Deletion of All Blocks
  71
- What Can be Done
  71
- How to Delete All Blocks
  71
- All Settings to Midposition
  71
- How to Set to Midposition
  71
- Undo All Settings to Midpos
  71
- How to Cancel 'Set to Midposition
  72
- R & B Convergence MID
  72
- What Can be Done
  72
- How to Set Convergence to Midposition
  72
- Undo R & B Convergence MID
  72
- How to Undo
  72
- Undo Green Convergence MID
  73
- What Can be Done
  73
- How to Undo
  73
- Green Convergence MID
  73
- How to Set Green Settings to Midposition
  73
- Common Settings
  73
- How to Select
  74
- G2 Adjustment
  74
- CRT Run in Cycle
  74
- What Can be Done
  74
- How to Select CRT Run in Cycle
  74
- Projector Warm up
  75
- What Can be Done
  75
- How to Select
  75
- Memory Banks
  75
- How to Select Memory Banks
  75
- How to Create a New Memory Bank
  75
- How to Recall a Specific Memorybank for the Actual Source
  76
- I2C Diagnostics
  76
- What Can be Seen
  76
- How to Select
  76
Programmable Function Keys

77
Messages, Warnings and Failures

79
Adjustment Blocks and Source Numbers 90 - 99

81
- Adjustment Blocks (Memory Blocks
  81
- What Are Adjustment Block
  81
- Built up of Block
  81
- Source Numbers 90 - 99
  81
- Why Used
  81
- How to Create a Second Block
  81

Advertisement

Advertisement

Related Products

Barco Categories

Projector

Monitor

Monitor Projector Accessories Controller Medical Equipment

More Barco Manuals