D-Link DWL-2600AP Administrator's Manual page 97

Unified Access Point Administrator's Guide
Field
Class Map Name
Match Every
Protocol
IPv4 Class Maps
Source IP Address
Source IP Mask
Destination IP
Address
Destination IP Mask
IPv6 Class Maps
Source IPv6
Address
Source IPv6 Prefix
Length
Destination IPv6
Address
Destination IPv6
Prefix Length
IPv6 Flow Label
January 2015
Description
Select name of the class to configure.
Use the fields in the Match Criteria Configuration area to match packets to a class. Select
the check box for each field to be used as a criterion for a class and enter data in the related
field. You can have multiple match criteria in a class.
Note: The match criteria fields that are available depend on whether the class map is an
IPv4 or IPv6 class map.
Select Match Every to specify that the match condition is true to all the parameters in an L3
packet.
All L3 packets will match an Match Every match condition.
Select the Protocol field to use an L3 or L4 protocol match condition based on the value of
the IP Protocol field in IPv4 packets or the Next Header field of IPv6 packets.
Once you select the field, choose the protocol to match by keyword or enter a protocol ID.
Select From List
Select one of the following protocols from the list:
•) IP
•) ICMP
•) IPv6
•) ICMPv6
•) IGMP
•) TCP
•) UDP
Match to Value
To match a protocol that is not listed by name, enter the protocol ID.
The protocol ID is a standard value assigned by the IANA. The range is a number from 0 –
255.
Select this field to require a packet's source IP address to match the address listed here.
Enter an IP address in the appropriate field to apply this criteria.
Enter the source IP address mask.
The mask for DiffServ is a network-style bit mask in IP dotted decimal format indicating
which part(s) of the destination IP Address to use for matching against packet content.
A DiffServ mask of 255.255.255.255 indicates that all bits are important, and a mask of
0.0.0.0 indicates that no bits are important. The opposite is true with an ACL wild card
mask. For example, to match the criteria to a single host address, use a DiffServ mask of
255.255.255.255. To match the criteria to a 24-bit subnet (for example 192.168.10.0/24), use
a mask of 255.255.255.0.
Select this field to require a packet's destination IP address to match the address listed
here. Enter an IP address in the appropriate field to apply this criteria.
Enter the destination IP address mask.
The mask for DiffServ is a network-style bit mask in IP dotted decimal format indicating
which part(s) of the destination IP Address to use for matching against packet content.
A DiffServ mask of 255.255.255.255 indicates that all bits are important, and a mask of
0.0.0.0 indicates that no bits are important. The opposite is true with an ACL wild card
mask. For example, to match the criteria to a single host address, use a DiffServ mask of
255.255.255.255. To match the criteria to a 24-bit subnet (for example 192.168.10.0/24), use
a mask of 255.255.255.0.
Select this field to require a packet's source IPv6 address to match the address listed here.
Enter an IPv6 address in the appropriate field to apply this criteria.
Enter the prefix length of the source IPv6 address.
Select this field to require a packet's destination IPv6 address to match the address listed
here. Enter an IPv6 address in the appropriate field to apply this criteria.
Enter the prefix length of the destination IPv6 address.
Flow label is 20-bit number that is unique to an IPv6 packet. It is used by end stations to
signify quality-of-service handling in routers (range 0 to 1048575).
Section 8 - Configuring Client Quality of Service (QoS)
Unified Access Point Administrator's Guide
Page 97