Detailed Discussions Of Bit 3; Detailed Discussions Of Bit 7; Sssw-Sw05; Detailed Discussions Of Bit 4 - Canon MF6500 Series Service Manual

Chapter 14
Any of the following error codes may be indicated at time of transmission
##0100, ##0280, ##0281, ##0750, ##0753, ##0754, ##0755, ##0758, ##0759, ##0760, ##0763 ##0764, ##0765, ##0768, ##0769,##0770, ##0773, ##0775, ##0778,
##0780, ##0783, ##0785, ##0788

14.1.3.3 Detailed Discussions of Bit 3

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Use it to select an appropriate reception mode after transmission of the CFR signal.
If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive'
for 'ECM reception.'
Memo:
Any of the following error codes may be indicated at time of reception because of line condition
##0107, ##0114, ##0201
Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.
When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal.

14.1.3.4 Detailed Discussions of Bit 4

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal.
If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.'

14.1.3.5 Detailed Discussions of Bit 6

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Selects whether or not to transmit CNG signal during manual transmission.
In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors due to failure to switch to fax mode, select "Transmitted" for the
CNG signal.

14.1.3.6 Detailed Discussions of Bit 7

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Selects whether or not to transmit CED signals during manual reception. If the other fax does not transmit even when you start manual reception, select "Transmit-
ted" for the CED signal.

14.1.4 SSSW-SW05

14.1.4.1 List of Functions

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Bit
0
1
2
3
4
5
6
7
14.1.4.2 Detailed Discussions of Bit 1
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.
Scanning direction in conversion follows the Bit 2 setting of SW14.

14.1.4.3 Detailed Discussions of Bit 2

LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text/photo mode while bit 1 is set to '1'.
Scanning direction in conversion follows the Bit 2 setting of SW14.

14.1.5 SSSW-SW12

14.1.5.1 List of Functions
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Bit
0
1
2
3
4
14-2
Download Free Service Manual And Resetter Printer at http://printer1.blogspot.com
Function
not used
Conversion from mm to inch (text mode)
Conversion from mm to inch (text/photo mode)
not used
not used
not used
not used
not used
Function
Time-out period for one page upon transmission
Time-out period for one page upon transmission
not used
not used
Time-out period for one page upon reception
T-14-4
1
-
convert
convert
-
-
-
-
-
T-14-5
1
1
1
-
-
1
0
-
do not convert
do not convert
-
-
-
-
-
0
0
0
-
-
0
0011-4099
0011-4100
0011-4101
0011-4102
0011-4103
0011-4104
0011-4105
0011-4106