Sharp MX-M260 Service Manual page 72

66-10
Purpose Adjustment/Setting/Check
Function (Purpose) Image data memory clear
Section FAX
Item Data
Operation/procedure
Select "1: YES" with the 10-key and press the [START] key. (When "2:
NO" is selected, the simulation is canceled.)
Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.
The management table is also cleared (initialized) at the same time.
* lIf there is any print data, the power must be turned off after clearing.
Note: Executable only when the FAX is installed.
66-11
Purpose Operation test/check
Function Used to send 300bps signals.
(Purpose) (Signal send level: Max.)
Section FAX
Item Operation
Operation/procedure
Select the signal number with the 10-key, and press the [START] key.
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [SYSTEM SET-
TINGS] key.)
The signal send level can be selected from 0dB or the soft SW set value.
The signal send level is returned to the soft SW set value before execu-
tion of the mode after completion of the mode.
By entering the number and pressing the [START] key during execu-
tion, the signal kind can be changed.
Item
1 NO SIGNAL
2 11111
3 11110
4 00000
5 010101
6 00001
Note: Executable only when the FAX is installed.
66-12
Purpose Operation test/check
Function Used to send 300bps signals.
(Purpose) (Signal send level: Set by soft SW)
Section FAX
Item Operation
Operation/procedure
Select the signal number with the 10-key, and press the [START] key.
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [SYSTEM SET-
TINGS] key.)
The signal send level can be selected from 0dB or the soft SW set value.
The signal send level is returned to the soft SW set value before execu-
tion of the mode after completion of the mode.
By entering the number and pressing the [START] key during execu-
tion, the signal kind can be changed.
Item
1 NO SIGNAL
2 11111
3 11110
4 00000
5 010101
6 00001
Note: Executable only when the FAX is installed.
66-13
Image data
Operation/procedure
Enter the number with the 10-key, [*] key, and [#] key.
Press the [CLEAR] key to return to the initial state.
Press the [START] key to register the entered number.
Note: Executable only when the FAX is installed.
66-14
Operation/Procedure
1. Select the item with the 10-key, and press the [START] key.
2. Set the make time with the 10-key.
The dial is sent with the set value + 26ms.
The sending dial cannot be interrupted.
Note: Executable only when the FAX is installed.
66-15
Operation/Procedure
1. Select the item with the 10-key, and press the [START] key.
2. Set the make time with the 10-key.
The dial is sent with the set value + 26ms.
The sending dial cannot be interrupted.
Note: Executable only when the FAX is installed.
66-16
Operation/Procedure
1. Select the item with the 10-key, and press the [START] key.
2. Enter the set value with the 10-key.
The sending dial cannot be interrupted.
MX-M260/M310/M260N/M310N SIMULATION 6 - 39
Purpose Setting
Function (Purpose) Used to register the dial numbers.
Section FAX
Item Operation
Purpose Operation check/test
Function
Used to perform the dial test. (10 PPS send test)
(Purpose)
Section FAX
Item Operation
Item Content
0 EXECUTE Execution
1 MAKE TIME Dial pulse make time setting
Purpose Operation check/test
Function
Used to perform the dial test. (20 PPS send test)
(Purpose)
Section FAX
Item Operation
Item Content
0 EXECUTE Execution
1 MAKE TIME Dial pulse make time setting
Purpose Operation check/test
Function
Used to perform the dial test. (DTFM signal send test)
(Purpose)
Section FAX
Item Operation
Item
0 EXECUTE
1 HIGH (SW)
2 HIGH-LOW (SW)
Setting range
–
0-15
Setting range
–
0-15
Setting
Content
range
Execution –
High group 0-15
High group, Low group 0-15