Sharp MX-M260 Service Manual page 66

3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item Content
1 TRAY1 1st tray
2 OPTION Option tray
3 MANUAL Manual feed
4 DUPLEX Back print
50-6
Purpose Adjustment
Function Used to adjust the print image position (top margin) on
(Purpose) print paper in the copy mode. (RSPF)
Item Picture quality
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item
Surface original scan start
1 SIDE1
position adjustment
Back original scan start
2 SIDE2
position set
Rear edge void adjustment
3 END EDGE
(RSPF)
Surface image loss quantity
4 LOSS(SIDE1)
set
5 LOSS(SIDE2) Back image loss quantity set
Surface rear edge image
6 REARLOS(SIDE1)
loss quantity set
Back rear edge image loss
7 REARLOS(SIDE2)
quantity set
50-8
The adjustments on the machine side must have been normally
completed.
Purpose Adjustment
Function (Purpose) FAX lead edge adjustment (read)
Section FAX
Operation/procedure
1. Select "1: COPY START."
The currently set value is highlighted beside the item.
2. Enter the correction value with the 10-key, and press the [#/P] key.
3. Press the [START] key.
Copying is started.
Normal display NOW PRINTING
DOOR OPEN
Error display JAM
PAPER EMPTY
There is no tray selection operation.
The optimum paper tray for the scanned size is selected.
Setting range Default
0-99
53
1-99
Image position
Setting
Content Default
range
1-99 50
1-99 50
1-99 50
1-5
1-5
1-5
1-5
MX-M260/M310/M260N/M310N SIMULATION 6 - 33
4. Select the scanning method.
Even when the SPF/RSPF is selected, if there is no original on the
SPF/RSPF, the OC is scanned.
Even when the OC is selected, if there is any original on the SPF/
RSPF, the SPF/RSPF is scanned. (Setting 2)
Item
1 COPY START Copy start
SCAN
2 SELECT (OC/
SPF/RSPF)
3 LEAD
4 LEFT
5 REAR
6 RIGHT
Note: Executable only when the FAX is installed.
50-9
Purpose
Function (Purpose)
Section
Operation/procedure
1. Select "1: COPY START."
The currently set value is highlighted beside the item.
2. Press the [START] key.
Copying is started.
Normal display
Error display
There is no tray selection operation.
The optimum paper tray for the scanned size is selected.
3
When two pages are scanned, duplex print is made,
3
Item
3
1 COPY START
3
2 LEAD
3 LEFT
4 REAR
LEAD
5
(DUPLEX)
6 LEFT (DUPLEX)
REAR
7
(DUPLEX)
Note: Executable only when the FAX is installed.
Content
Scan selection (1: OC,
2: SPF, 3: RSPF back)
Scan lead edge position
adjustment value of the
selected method in 2.
Scan left edge position
adjustment value of the
selected method in 2.
Scan rear edge position
adjustment value of the
selected method in 2.
Scan right edge position
adjustment value of the
selected method in 2.
Adjustment
FAX lead edge adjustment (print)
FAX
NOW PRINTING
DOOR OPEN
JAM
PAPER EMPTY
Content
Copy start
Print lead edge void
adjustment value
(Front surface)
Print left edge void
adjustment value
(Front surface)
Print rear edge void
adjustment value
(Front surface)
Print lead edge void
adjustment value
(Back surface)
Print left edge void
adjustment value
(Back surface)
Print rear edge void
adjustment value
(Back surface)
Setting
Default
range
– –
1-3 1
43-57 50
43-57 50
43-57 50
43-57 50
Setting
Default
range
– –
43-57 53
43-57 53
43-57 53
43-57 53
43-57 53
43-57 53