Sharp MX-M260 Service Manual page 67

50-10
Purpose Adjustment
Used to adjust the print image center position.
Function
(Adjustment can be made for each paper feed
(Purpose)
section.)
Section Image processing (ICU)
Item Picture quality
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item Content
1 BYPASS Manual paper feed
2 TRAY1 1st tray
3 TRAY2 2nd tray
4 TRAY3 3rd tray
5 TRAY4 4th tray
6 DUPLEX Back print
50-12
Purpose Adjustment
Function Used to adjust the print image center position.
(Purpose) (Adjustment can be made for each document mode.)
Section Image processing
Item Picture quality
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item Content
1 OC OC document scan
RSPF document front
2 SPF(SIDE1)
surface scan
RSPF document back
3 SPF(SIDE2)
surface scan
Image position
Setting range Default
1-99 50
Image position
Setting range Default
1-99 50
MX-M260/M310/M260N/M310N SIMULATION 6 - 34
51
51-1
Purpose Adjustment
Function
Used to adjust the OPC drum separation pawl ON time.
(Purpose)
Image process
Section
(Photoconductor/Developing/Transfer/Cleaning)
Item Operation
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key.
Item Setting range
1 145mm/s
1-99
2 122mm/s
51-2
Purpose Adjustment
Used to adjust the contact pressure of paper onto the
resist roller in each section (copier paper feed section,
Function duplex paper feed section, RSPF paper feed section).
(Purpose) (When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Press the [START] key.
The display is shifted to the copy menu.
3. Select the paper feed tray and the print density.
Enter the adjustment value with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item Content
1 BYPASS Manual feed
2 TRAY1 1st tray
3 TRAY2 2nd tray
4 TRAY3 3rd tray
5 TRAY4 4th tray
6 DUPLEX Back print
7 SPF(SIDE1) RSPF front surface
8 SPF(SIDE2) RSPF back surface
51-8
Purpose Setting
Function Used to set the OPC drum separation pawl operation
(Purpose) inhibit. (ON/OFF)
Image process
Section
(Photoconductor/Developing/Transfer/Cleaning)
Item Operation
Operation/procedure
Select the set value with the 10-key.
Item Content
0 ON Enable
1 OFF Disable
Default
50
Setting range Default
1-99 50
1-99 50
1-99 50
1-99 50
1-99 50
1-99 70
1-99 50
1-99 50
Setting range Default
0-1 0