Sharp MX-M260 Service Manual page 70

66
66-1
Purpose Setting
Function
Used to change and check the FAX-related soft SW.
(Purpose)
Section FAX
Operation/procedure
1. Enter the soft SW number to be selected with the 10-key.
2. Check and change the setting content of the selected soft SW.
3. Press the [START] key to save the set content.
The FAX-related soft SW is displayed on the LCD, and changing can
be made by monitoring it.
Note: Executable only when the FAX is installed.
66-2
Purpose Adjustment
Function Used to clear the FAX-related soft SW.
(Purpose) (Except for the FAX adjustment values)
Section FAX
Operation/procedure
1. Enter the country code with the 10-key, and press the [START] key.
2. When "1: (YES)" is selected, the soft SW corresponding to the
country code is cleared. When "2: (NO)" is selected, the simulation
is canceled.
Country code
Japan : 00000000
U.S.A. : 10110101
Australia : 00001001
U.K. : 10110100
France : 00111101
Germany : 00000100
Sweden : 10100101
New Zealand : 01111110
China : 00100110
Singapore : 10011100
Taiwan : 11111110
India : 01010011
Malaysia : 01101100
Hong Kong : 01010000
Middle east : 11111101
SouthAfrica : 10011111
Spain : 10100000
Portugal : 10001011
Russia : 10111000
Denmark : 00110001
Norway : 10000010
Switzerland : 10100110
Italy : 01011001
Belgium : 00001111
Luxembourg : 01101001
Netherlands : 01111011
Finland : 00111100
The codes other than the above are accepted as Japan.
Note: Executable only when the FAX is installed.
Operation/procedure
Press the [START] key.
Read/write can be checked for FAX PWB memory.
The check result is displayed separately for each memory.
1. Memory to be checked
2. Detailed procedure
Interruption cannot be made during operation.
Note: Executable only when the FAX is installed.
Operation/procedure
Select the signal number with the 10-key, and press the [START] key.
The signal is sent to the line and the machine speaker. (Sending the
signal is continued until the [SYSTEM SETTINGS] key is pressed.)
By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.
MX-M260/M310/M260N/M310N SIMULATION 6 - 37
66-3
Purpose Operation test/check
Function (Purpose) FAX PWB memory check
Section FAX
Item Operation
DRAM
SRAM
Program area
Flash ROM
Memory area
Option memory
PAGE
MODEM
"55H" is written to all the addresses of each memory, and the
1 address data are read in sequence to check that they were
properly written.
"AAH" is written to all the addresses of each memory, and the
2 address data are read in sequence to check that they were
properly written.
"00H" is written to all the addresses of each memory, and the
3 address data are read in sequence to check that they were
properly written.
Perform checks 1 - 3 sequentially. If there is no abnormality, it is
4 "OK." If there is any abnormality, "NG" is notified to the error
address.
The check result is saved. New result is overwrited with each
5
check.
66-4
Purpose Operation test/check
Function
Signal send mode (Signal send level: Max.)
(Purpose)
Section FAX
Item Operation
Item
1 NO SIGNAL Signal not sent
2 33.6 V34 33.6 V34
3 31.2 V34 31.2 V34
4 28.8 V34 28.8 V34
5 26.4 V34 26.4 V34
6 24.0 V34 24.0 V34
7 21.6 V34 21.6 V34
8 19.2 V34 19.2 V34
9 16.8 V34 16.8 V34
10 14.4 V34 14.4 V34
11 12.0 V34 12.0 V34
12 9.6 V34 9.6 V34
13 7.2 V34 7.2 V34
SUM check only
The memory size follows the
automatically detected value.
Send signal