Sony HVR-A1J Service Manual page 169

1-2-2. Initialization of 8, C, 13, 18, 1C Page Data
1. Initializing of 8, C, 13, 18, 1C Page Data
Note1: If "Initialization of Pages 8, C, 13, 18, 1C" is executed,
all data on pages 8, C, 13, 18, 1C are initialized. (Only
an individual page cannot be initialized)
Note2 : If the 8, C, 13, 18, 1C page data has been initialized, the
following adjustments need to be performed again.
1) Modification of 8, C, 13, 18, 1C page data
2) Electronic viewfinder system adjustments (if all areas
were initialized)
3) LCD system adjustments (if all areas were initialized)
4) Node unique ID No. input (if all areas were initial-
ized)
5) Servo, RF system adjustments (if all areas were ini-
tialized)
6) Video system adjustments (if all areas were initial-
ized)
Adjustment Page 8
Adjustment Address 00 to FF
Adjustment Page C
Adjustment Address 10 to FF
Adjustment Page 13
Adjustment Address 00 to FF
Adjustment Page 18
Adjustment Address 00 to FF
Adjustment Page 1C
Adjustment Address 00 to FF
Initializing method:
Order Page Address Data
1 0 01 01
2 0 10 00
3 3 81
4 3 80 0C
5 3 80
6
Note 3: If other than adjustment address was initialized, the ad-
justed data is not initialized.
HVR-A1J/A1U/A1N/A1E/A1P/A1C
Procedure
Set the following data, and
press PAUSE (Write) button.
(Note 3)
00: Initializing all areas
01: Initializing other than
adjustment address
Press PAUSE (Write) button.
Check the data changes to
"1C".
Perform "Modification of 8,
C, 18, 1C Page Data"
2. Modification of 8, C, 13, 18, 1C Page Data
If the 8, C, 13, 18, 1C page data has been initialized, change the
data of the "Fixed data-2" address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages 8, C, set data: 00 to page: 0,
address: 10, and then select pages 8, C.
3) If modification of data on pages 13, 18, 1C, set data: 01 to
page: 0, address: 10, and then select pages 3, 8, C.
After the modification of data finished, return the data on page:
0, address: 10 to "00".
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
6) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table.
If different, change them to the adjustment initial values.
Processing after Completing Modification 8, C, 13, 18, 1C
page data:
Order Page Address Data
1 0 10
2 2 00
3 2 01
3. 8 Page table
Note 1: Check that the data of page: 0, address: 10 is"00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the 8, C, 13, 18, 1C Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of 8, C, 13, 18, 1C Page Data")
Initial value
Address
NTSC PAL
00
01 to 11
12
13 to 78
79
7A
7B
7C, 7D
7E
7F to FF
6-10
Procedure
00
29
29 Press PAUSE (Write) button.
Remark
Fixed data-2
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)