ADEMCO VISTA-20P Installation And Setup Manual page 26

Installation Instructions
Interactive Mode Programming (∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82)
Entering Interactive Mode
Loading Factory Defaults/Initializing for Download
To Load Default Entries
To Initialize Download ID
Do not press
programmed into the system will be changed!
Exiting the Programming Mode
Prevent installer code reentry
Allow installer code reentry
Table of Device Addresses
††
Address Report
00 100
03 103
04 104
07 107
08 108
†
09 109
†
10 110
†
11 111
12 112
13 113
†
14 114
†
15 115
16 n/a
17 n/a
18 n/a
19 n/a
20 n/a
21 n/a
22 n/a
23 n/a
28 n/a
† 4219/4229 addresses 9-11 and 4204 addresses 14-15 apply to the VISTA-20P only.
†† Addressable devices are identified by "1" plus the device address when reporting. Enter a report
code for zone 91 to enable addressable device reporting (default = reports enabled). See field *199
for addressable device (ECP) 3-digit/2-digit identification keypad display options.
3-6
Press [ ∗ ] + [Interactive Mode No.] (for example, ∗ 56) while in Program Mode.
The Alpha display keypad will display the first of a series of prompts
requesting entries.
After making the appropriate entry, press the [∗] key to accept the entry and
continue to the next prompt.
Press ∗97 while in Program Mode. This resets all data fields to the default
values shown in the boxes in the Program Form. Use ∗ 97 only if you wish to
return to the original factory-programmed defaults.
Press ∗96 while in Program Mode. This initializes the system for
downloading and resets all the subscriber account numbers and CSID.
✱
97 to load defaults if any programming has been done previously—data already
Press ∗98. Exits Programming Mode and prevents re-entry by:
Installer Code + [8] + [0] + [0]. To enter the programming mode if ∗ 98 was
used to exit, you must first power the system down. Then power up again,
and press [∗] and [#] at the same time, within 50 seconds of powering up.
Press ∗99. Exits Programming Mode and allows re-entry by:
Installer Code + [ 8] + [0] + [0] or by: Pressing [∗] and [#] at the same time,
within 50 seconds of power-up.
Device
RF Receiver
Long Range Radio
4286 Voice Module
Zone Expanders (4219/4229):
module 1 zones 09 - 16
module 2 zones 17 - 24
module 3 zones 25 - 32
module 4 zones 33 - 40
module 5 zones 41 - 48
Relay Modules (4204):
module 1
module 2
module 3
module 4
Keypads:
keypad 1
keypad 2
keypad 3
keypad 4
keypad 5
keypad 6
keypad 7
keypad 8
5800TM Module
Programmed by...
*56 zone programming: input device type entry
automatic if output to long range radio field *29 enabled
automatic if phone module access code field *28 enabled
*56 zone programming: input device type entry, then:
• automatic if zone no. 9-16 entered as AW type or relay assigned
• automatic if zone no. 17-24 entered as AW type or relay assigned
• automatic if zone no. 25-32 entered as AW type or relay assigned
• automatic if zone no. 33-40 entered as AW type or relay assigned
• automatic if zone no. 41-48 entered as AW type or relay assigned
*79 output device programming: device address prompt:
• entered at device address prompt
• entered at device address prompt
• entered at device address prompt
• entered at device address prompt
data field programming as listed below:
• always enabled for partition 1, all sounds enabled.
• data field *190
• data field *191
• data field *192
• data field *193
• data field *194
• data field *195
• data field *196
automatic