Installing The Rf Receiver; Installing A 5800Tm Module; Installing The Transmitters - ADEMCO VISTA-20P Installation And Setup Manual

Installation Instructions

Installing the RF Receiver

You must use one of the following receivers:
RF Receiver
5881L/5882L
5881M/5882M
5881H/5882H
1. Set Device Address to "00" as described in its
instructions (set all switches to the right, "off"
position).
2. Mount the receiver, noting that the RF receiver can
detect signals from transmitters within a nominal
range of 200 feet.
3. Connect the receiver's wire harness to the control's
keypad terminals. Plug the connector at the other
end of the harness into the receiver. Refer to the
installation instructions provided with the receiver
for further installation procedures regarding antenna
mounting, etc.

Installing a 5800TM Module

1. Mount the 5800TM next to the RF receiver (between
one and two feet from the receiver's antennas) using
its accompanying mounting bracket. Do not install
within the control cabinet.
2. Connect the 5800TM to the control panel's keypad
connection terminals as shown on the Summary of
Connections diagram and set to address 28.

Installing the Transmitters

1. To be sure reception of the transmitter's signal at the
proposed mounting location is adequate, perform a
Go/No Go Test, described in the Testing the System
section.
2. Install transmitters in accordance with the
instructions provided with each.
3. Set 5827, 5827BD, 5804BD transmitters to the
programmed House ID (field *24), using its DIP
switches.
ULC NOTE: In accordance with ULC standards, the
RF supervision period for the VISTA-20PCN and
VISTA-15PCN is three hours for Fire zones (Zone Type
9) and 12 hours for all other zone types.
2-8
No. of Zones
up to 8
up to 16
VISTA-20P = up to 40
VISTA-15P = up to 26
NOTE: CIRCUIT BOARD IS MOUNTED IN
CONTROL'S CABINET, GROUNDING LUGS (2)
PROVIDED MUST BE INSERTED IN LEFT-
HAND TERMINALS OF ANTENNA BLOCKS AND
SECURED TO CABINET (SEE RECEIVER'S
AND CONTROL'S INSTRUCTIONS)
MOUNTING
INTERFERENCE
HOLES
TO RELEASE CIRCUIT BOARD,
REMOVE SCREWS (2)
AND BEND BACK TABS (2).
Figure 9. 5881/5882 RF Receiver (cover removed)
Notes
• The receiver is supervised and a trouble report is
sent ("CHECK 100" displayed) if communication
between the panel and receiver is interrupted, or
if no valid RF signals from at least one
supervised transmitter are received within 12
hours.
If the receiver is mounted remotely:
• Place the RF receiver in a high, centrally located
area for best reception.
• Do not locate the receiver or transmitters on or
near metal objects. This will decrease range
and/or block transmissions.
• Do not locate the RF receiver in an area of high
RF interference (indicated by frequent or
prolonged lighting of the LED in the receiver;
random flicker is OK).
• Do not locate RF receiver closer than 10 feet
from any keypads to avoid interference from the
microprocessors in those units.
ANTENNAS
MODEL No. IS INDICATED
ON CIRCUIT BOARD
INSERT IN
RIGHT-HAND
TERMINALS
@ @ h ? @ @ h ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ h ? @ @ h ? @ @ h ? @ @ h ? @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @ 5882
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ LOCATION
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @
@ @ g @ @ g ? @ @ ? @ @
CIRCUIT @ @ g @ @ g @ @ @ @ @ @ @ @ @ @ g @ @ g ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? @ @ ? @ @ ? @ @ ? @ @
@ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @
PLUG
BOARD
&
SOCKET
DIP SWITCH
INDICATOR
LED
Notes
• Use this module only if you are using one or
more 5827BD Wireless Bi-directional Keypads or
5804BD Transmitters.
• The 5800TM must be set to address 28 (cut red-
W1 jumper).
• The 5800TM can be used in partition 1 only.
• For additional information regarding the
5800TM, refer to the 5800TM's instructions.
Notes
• Refer to the table of compatible devices at the
back of this manual.
• Supervised transmitters
the receiver at 70-90 minute intervals. If at least
one check-in message is not received from each
transmitter within a 12-hour period, the "missing"
transmitter number(s) and "CHECK" is displayed.
†
Hand-held transmitters (e.g., 5802, 5802CP, 5804,
5804BD, 5827, 5827BD) do not send check-in signals.
U L
The following transmitters are not intended for use
in UL installations: 5802MN, 5802MN2, 5804, 5804BD,
5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.
The 5827BD and 5800TM can be used in UL Listed
Residential Burglar installations.
YELLOW
}
RED
TO CONTROL'S
BLACK
REMOTE KEYPAD
GREEN
CONNECTION
POINTS.
WIRING
OPENING
KNOCKOUT
AREA FOR
SURFACE
WIRING
†
send check-in signals to