Specifications - Roland CammJet CJ-500 User Manual

Specifications

Specifications
Printing/Cutting method
Printing/Cutting area
Sheet material
Acceptable
material widths
Roll material
Width of material that can be cut off
Conditions for usable materials
Ink
Pigment ink
cartridges
Capacity
Color
Dye ink
Capacity
Color
Apparent colors
Printing resolution (Printing dot resolution)
Distance accuracy (When printing)
Acceptable tool
Cutting speed
Blade force
Blade offset compensation
Software resolution (When cutting)
Distance accuracy (When cutting)
Repetition accuracy (When cutting)
Repetition between printing and cutting
Alignment accuracy for printing and
cutting when reloading material
92
CJ-500
Piezo ink-jet method/media-moving method
1346.2 mm x 24998 mm (53 in. x 984-1/8 in.)
90 to 1371 mm (3.5 to 54 in.)
(Note that detection of the front and rear edges is not possible for material measuring from 90 mm to 430 mm (3.5 to 17 in.).)
90 to 1371 mm (3.5 to 54 in.)
(Note that detection of the front and rear edges is not possible for material measuring from 90 mm to 430 mm (3.5 to 17 in.).)
90 to 1371 mm (3.5 to 54 in.)
-Cuttable material thickness: 0.08 to 0.22 mm (0.00315 to 0.00866 in.) (depending on material composition)
-Maximum cuttable material thickness including base paper (backing paper): 0.4 mm (0.0157 in.)
-Maximum printable material thickness including base paper (backing paper): 1.0 mm (0.039 in.)
-Maximum diameter for roll material: 180 mm (7-1/16 in.)
-Core inner diameter for roll material: 50.8 mm (2 in.) or 76.2 mm (3 in.)
-Maximum weight for roll material: CJ-500.....20 kg (44.1 lb.)
Six colors: the four colors cyan, magenta, yellow, and black, plus either light cyan
Cyan, magenta, yellow, black, light cyan, and light magenta
1440 dpi x 720 dpi / 720 dpi x 720 dpi / 540 dpi x 540 dpi / 360 dpi x 720 dpi / 180 dpi x 720 dpi
Error of less than ±0.3% of distance traveled, or 0.3 mm, whichever is greater
(at Roland PET-film, print travel: 1 m (39-3/8 in.)
Cutter (blade and blade holder): Special blade for CAMM-1 series
10—600 mm/s (10 to 300 mm/s in the material-feed direction)
Error of less than ±0.4% of distance traveled, or 0.3 mm, whichever is greater
When distance correction has been performed (when the setting for [CALIBRATION] - [CUTTING ADJ.] has been made):
Error of less than ±0.2% of distance traveled, or 0.1 mm, whichever is greater
0.1 mm or less (excluding stretching/contraction of the material)
Range for assured repetition accuracy (*1)
For materials with a width exceeding 610 mm (24 in.): Length 4,000 mm (157-7/16 in.)
For materials with a width of 610 mm (24 in.) or less : Length 8,000 mm (315-15/16 in.)
(excluding possible shift caused by expansion/contraction of the material and/or by reloading the material,
and provided that material length is under 3000 mm (118-1/16 in.)
Error of less than ±0.3% of distance traveled, or 2 mm, whichever is greater
[Guaranteed area of alignment for printing and cutting when reloading the material] (*2)
1092.2 mm x 24998 mm (43 in. x 984-1/8 in.)
90 to 1117 mm (3.5 to 44 in.)
90 to 1117 mm (3.5 to 44 in.)
90 to 1117 mm (3.5 to 44 in.)
CJ-400.....17 kg (37.5 lb.)
Exclusive pigment-ink cartridge
220 cc ±5 cc
and light magenta or orange and green
Exclusive dye-ink cartridge
220 cc ±5 cc
16.7 million colors
30 to 200 gf
0.000 to 1.500 mm (0 to 0.0591 in.)
0.025 mm/step (0.00984 in./step)
±0.5 mm (±0.0197 in.) max. at 25°C
For items indicates by an asterisk "(*)", please see the next page.
CJ-400
(when head is raised to maximum)
Continued on the next page