Roland GX-640/GX-500/GX-400/GX-300 Setup Manual
  1. Manuals
  2. Brands
  3. Roland Manuals
  4. Printer
  5. GX-640/GX-500/GX-400/GX-300
  6. Setup manual

Roland GX-640/GX-500/GX-400/GX-300 Setup Manual

Sign maker
Hide thumbs
Table of Contents

Advertisement

Quick Links

Setup Guide
GX-640/GX-500/GX-400/GX-300
BE SURE TO READ THIS FIRST
This document describes the included items and accessories, program installation and
setup, and other important matters. Be sure to read this manual before use.
Thank you very much for purchasing this product.
 To ensure correct and safe usage with a full understanding of this product's performance, please besure to read
through this manual completely and store it in a safe location.
 Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
 The contents of this operation manual and the specifications of this product are subject to change without
notice.
 The operation manual and the product have been prepared and tested as much as possible. If youfind any
misprint or error, please inform us.
 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which mayoccur through
use of this product, regardless of any failure to perform on the part of this product.
 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which mayoccur with respect
to any article made using this product.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GX-640/GX-500/GX-400/GX-300 and is the answer not in the manual?

Questions and answers

Related Manuals for Roland GX-640/GX-500/GX-400/GX-300

Summary of Contents for Roland GX-640/GX-500/GX-400/GX-300

  • Page 1  Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which mayoccur with respect to any article made using this product.

  • Page 3: Table Of Contents

    This document is the setup guide for four models: GX-640/500/400/300. Also, most of the figures in this document depict the GX-500 Company names and product names are trademarks or registered trademarks of their respective holders. http://www.rolanddg.com/ Copyright © 2010 Roland DG Corporation...

  • Page 4: To Ensure Safe Use

    To Ensure Safe Use Improper handling or operation of this machine may result in injury or damage to property. Points which must be observed to prevent such injury or damage are described as follows. About WARNING and CAUTION Notices Used for instructions intended to alert the user to the risk of death or severe WARNING injury should the unit be used improperly.
  • Page 5 To Ensure Safe Use Incorrect operation may cause injury. WARNING WARNING Be sure to follow the operation proce- Never attempt to disassemble, repair, or dures described in this documentation. modify the machine. Never allow anyone unfamiliar with the Doing so may result in fire, electrical shock, usage or handling of the machine to or injury.
  • Page 6 Contact your shock. If anything gets inside, immediately authorized Roland DG Corp. dealer. disconnect the power cord and contact your authorized Roland DG Corp. dealer. Never place any flammable object nearby.
  • Page 7 To Ensure Safe Use Important notes about the power cord, plug, and electrical outlet Never place any object on top or subject to Never allow to get wet. damage. Never bend or twist with undue force. Never make hot. Never pull with undue force. Dust may cause fire.
  • Page 8 To Ensure Safe Use The total weigh of this machine reaches about 70kg (154 lb.). WARNING WARNING Install the machine in a location that is Be sure to lock the stand's casters. level, stable, and able to bear the weight If the machine should begin to topple, a ma- of the machine.

  • Page 9: Warning Labels

    To Ensure Safe Use Warning Labels Warning labels are affixed to make areas of danger immediately clear. The meanings of these labels are as follows. Be sure to heed their warnings. Also, never remove the labels or allow them to become obscured. Caution: Moving Print Heads The tool carriage moves at high speed and pose a hazard.

  • Page 10: Pour Utiliser En Toute Sécurité

    Pour utiliser en toute sécurité La manipulation ou l'utilisation inadéquates de cet appareil peuvent causer des blessures ou des dommages matériels. Les précautions à prendre pour prévenir les blessures ou les dommages sont décrites ci-dessous. Avis sur les avertissements Utilisé pour avertir l'utilisateur d'un risque de décès ou de blessure grave ATTENTION en cas de mauvaise utilisation de l'appareil.
  • Page 11 Pour utiliser en toute sécurité L'utilisation incorrecte peut causer des blessures ATTENTION ATTENTION S'assurer de suivre les procédures Débrancher le câble d'alimentation avant d'utilisation décrites dans la documen- de procéder au nettoyage ou à l'entretien tation. Ne jamais permettre à quiconque de l'appareil, et avant d'y fixer ou d'en ne connaît pas le fonctionnement ou la retirer des accessoires en option.
  • Page 12 Ne jamais utiliser si un composant est le câble d'alimentation et communiquer avec endommagé. le représentant Roland DG Corp. autorisé. Continuer à utiliser l'appareil peut causer un incendie, un choc électrique ou des bles- Ne jamais placer d'objet inflammable à...
  • Page 13 Pour utiliser en toute sécurité Remarques importantes à propos du câble d'alimentation, de la fiche et de la prise électrique Ne jamais déposer aucun objet sur le câble, sur Ne jamais laisser l'eau toucher le câble, la fiche la fiche ou sur la prise car cela risque de les ou la prise.
  • Page 14 Pour utiliser en toute sécurité Le poids total de l’appareil peut être de 70 kg (154 lb.) ATTENTION ATTENTION Installer l'appareil à un endroit stable et S'assurer de verrouiller les roulettes de plat et capable de supporter son poids. la base. Le poids total de l’appareil peut être de 70 Si l'appareil devait commencer à...
  • Page 15 Pour utiliser en toute sécurité Vignettes d'avertissement Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones dangereuses. La signification des vignettes est donnée ci-dessous. Respecter les avertisse- ments. Ne jamais retirer les vignettes et ne pas les laisser s'encrasser. Attention : Chariot mobile Le chariot de coupe se déplace très rapidement et peut être...

  • Page 16: Important Notes On Handling And Use

    Important Notes on Handling and Use This machine is a precision device. To ensure the full performance of this machine, be sure to observe the following important points. Failure to observe these may not only result in loss of performance, but may also cause malfunction or breakdown. Main unit This Machine Is a Precision Device ...

  • Page 17: About The Documentation For This Machine

    About the Documentation for This Machine Documentation Included with the Machine CAMM-1PRO Setup Guide (This document) This describes how to install and set up the machine and the included software. CAMM-1PRO User's Manual This describes how to use and care for the machine, and explains what to do if a problem occurs. PNS-642/502/402/302 Assembly Instructions (shipped with the stand) This document describes the assembly and installation of the special stand.

  • Page 19: Chapter 1 Setup Preparation

    Chapter 1 Setup Preparation...

  • Page 20: Included Items

    1-1 Included Items The following items are packed together with the unit. Make sure they are all present and accounted for. Blade holder/Pin(one for Power cord(1) Blade(1) Alignment tool(1) each ) Replacement blades for Cable clamp (1) CD-ROM (1) USB cable (1) separating knife (1) Setup Guide User’s Manual(1)

  • Page 21: Installing

    1-2 Installing Deciding On an Installation Site Install in a stable location offering good operating conditions. An unsuitable location can cause accident, faulty operation, or breakdown. WARNING Never use out of doors or in any location where exposure to water or high humidity may occur.

  • Page 22: Assembling The Stand

    1-2 Installing Assembling the Stand For an explanation of how to assemble the unit and the stand (PNS-642/502/402/302), refer to the “ASSEMBLY INSTRUCTIONS” included with the stand. CAUTION Use the joining screws to secure the unit to the stand. Failure to do so may result in falling of the unit, leading to injury. CAUTION Use care to avoid pinching the fingers when placing the unit on the stand.

  • Page 23: Connecting The Cables

    1-2 Installing Connecting the Cables WARNING Connect to an electrical outlet that complies with this machine's ratings (for voltage, frequency, and current). Incorrect voltage or insufficient current may cause fire or electrical shock. WARNING Handle the power cord, plug, and electrical outlet correctly and with care. Never use any article that is damaged.

  • Page 24: Usb Connection

    Never use a USB hub or the like. Serial Connection (Windows only) Use a serial cable from Roland DG Corp. sold separately (for an IBM-compatible computer, use a crossover cable such as the XY-RS-34) or equivalent. A straight cable such as a modem cable will not work.

  • Page 25: Chapter 2 Installing Software

    Chapter 2 Installing Software...

  • Page 26: About The Included Software

    This is a Windows-based driver required for sending data from a computer to the machine. Be sure to install ■ Roland CutStudio Roland CutStudio is software that allows you to create cutting data and easily perform cutting operations. ■ CutStudio Plug-in for Adobe Illustrator This is an Illustrator software plug-in that lets you cut from data created in Adobe Illustrator.

  • Page 27: If You're Using A Windows

    (This includes such computers later upgraded to Windows Vista/7.) 2) Computers on which USB operation is assured by the manufacturer of computers System Requirements for the Roland CutStudio Operating Systems Windows XP/Vista/7 (32 bit edition/64 bit edition) Computer Computer running Windows...

  • Page 28: Installing The Software

    Before you start installation and setup, make sure the USB cable is not connected.  Log on to Windows as "Administrators" right.  Insert the Roland Software Package CD-ROM into the computer. (Windows Vista/7: When the automatic playback window appears, click [Run menu. exe].) The setup menu appears as below automatically.

  • Page 29: What To Do If Installation Is Impossible (Usb Connection)

    2-2 If You're Using a Windows Installing CutStudio Install the cutting software "CutStudio." Procedure  Display the setup menu of the Roland CAMM-1PRO Software Package.  Click [Install]. The setup window appears. Windows Vista/7: When [User Account Control] window appears on the screen, click [Yes].

  • Page 30: Uninstalling The Driver

    2-2 If You're Using a Windows  Delete the model name you're using. (or [Unknown device]). Go to the [Action] menu, At the [View] menu, click and click [Uninstall]. [Show hidden devices]. Find [Printers] or [Other de- vice], then double-click it. Click the model name you're using (or [Unknown device]).
  • Page 31 When the window shown at left appears, click [Yes].  Insert the Roland Software Package CD-ROM into the computer. If the setup menu appears, go to the upper right and click the to close it.  Windows Vista/7: Hold "Windows button" and press "R" buttons.

  • Page 32: If You're Using A Macintosh

    Procedure  Insert the included CD-ROM into the CD-ROM drive.  Double-click the [Roland CAMM-1PRO] icon that appears on the desktop.  Double-click the "Install_e.html" icon. The [Mac OS Installation and Setup Guide] appears. ...

  • Page 34: Software License Agreement

    Please read this agreement before unpacking the media Software license agreement Roland DG Corporation (hereinafter referred to as the “Company”) shall grant you a non-transferable, non-exclusive right to use the Software supplied with this Agreement, on the condition that you agree to the following provi- sions.

This manual is also suitable for:

Camm-1 pro gx-640Camm-1 pro gx-500Camm-1 pro gx-400Camm-1 pro gx-300

Table of Contents