Sony HAP-S1 Service Manual page 34

HAP-S1
4-4-4. FAN Control Check
It can change the fan motor speed.
Procedure:
1. Enter the "4. LCD/Others" mode.
(Refer to "4-4. LCD/Others" on page 33)
2. Rotate the [PUSH ENTER] knob to select the "4. FAN Control
Check".
3. Press the [PUSH ENTER] knob to enter the "4. FAN Control
Check" mode.
4-4.FAN Control Check
1. fan off (HAP-Z1ES only)
2. fan slow
3. fan mid (HAP-S1 only)
4. fan high
5. Back to LCD/Others Menu
Note: "1. fan off (HAP-Z1ES only)" cannot use in this unit.
4. Rotate the [PUSH ENTER] knob to select the "2. fan slow"
and press the [PUSH ENTER] knob.
5. The fan motor is changed to slow speed.
6. Rotate the [PUSH ENTER] knob to select the "3. fan mid
(HAP-S1 only)" and press the [PUSH ENTER] knob.
7. The fan motor is changed to medium speed.
8. Rotate the [PUSH ENTER] knob to select the "4. fan high"
and press the [PUSH ENTER] knob.
9. The fan motor is changed to high speed.
34
4-5. HDD
It can display the hard disk drive information.
Procedure:
1. Enter the service DIAG mode.
(Refer to "1. Entering Method of The Service DIAG Mode" on
page 31)
2. Rotate the [PUSH ENTER] knob to select the "5. HDD".
3. Press the [PUSH ENTER] knob to enter the "5. HDD" mode.
Note 1: When the hard disk drive is damaged, the information (model
name, serial number and fi rmware revision) of hard disk drive is
not displayed on the liquid crystal display.
In addition, when the cable connected to the hard disk drive is
disconnected or broken, the information of hard disk drive is not
displayed on the liquid crystal display.
When the information of hard disk drive is not displayed, check
the cable connected to the hard disk drive. When the cable is bro-
ken, replace it and enter the "5. HDD" mode again.
5.HDD
1. Model TOSHIBA MQ01ABF050
2. Serial
3. Firmware Rev.
4. SMART Data Read(Need USB Memory)
5. SMART Short Test (2min)
6. SMART Long Test (2-4 hours)
5.HDD
2. Serial
3. Firmware Rev.
4. SMART Data Read(Need USB Memory)
5. SMART Short Test (2min)
6. SMART Long Test (2-4 hours)
7. Back to Main Menu
(Displayed characters/values in the above fi gure are example)
Note 2: Refer to "HDD CHECK" for the "5. SMART Short Test (2min)"
mode and "6. SMART Long Test (2-4 hours)" mode on page 38.
4. Connect a USB memory (FAT32 formatted) to the USB con-
nector on the main unit.
5. Rotate the [PUSH ENTER] knob to select the "4. SMART
Data Read(Need USB Memory)" and press the [PUSH EN-
TER] knob.
(When a USB memory is not connected to the USB connector
on the main unit, "Failed to save USB memory" is displayed
on the liquid crystal display. But the SMART data is displayed
on the liquid crystal display)
5-4.SMART Data Read
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
The data was saved to USB memory
Back to HDD Menu
XXX...: SMART data
53TSC1MGT
AM001Y
53TSC1MGT
AM001Y