Step 2 Inserting A Cassette - Sony DCR-TRV820 Service Manual

Step 1 Preparing the power
supply
The remaining battery time indicator
The indicator may not be correct, depending on
the conditions in which you are recording. When
you close the LCD panel and open it again, it
takes about 1 minute for the correct remaining
battery time to be displayed.
If the power may go off although the battery
remaining indicator indicates that the battery
pack has enough power to operate
Charge the battery pack fully again so that the
indication on the battery remaining indicator is
correct.
What is "InfoLITHIUM"?
The "InfoLITHIUM" is a lithium ion battery pack
which can exchange data such as battery
consumption with compatible electronic
equipment. This unit is compatible with the
"InfoLITHIUM" battery pack (L series). Your
camcorder operates only with the
"InfoLITHIUM" battery. "InfoLITHIUM" battery
packs have the mark.
"InfoLITHIUM" is a trademark of Sony
Corporation.
20
Step 2 Inserting a
cassette
We recommend using Hi8 /Digital8 video
cassettes.
(1) Prepare the power supply (p. 15).
(2) Open the lid of the cassette compartment, and
press EJECT. The cassette compartment opens
automatically.
(3) Insert a cassette with its window facing out
and the write-protect tab on the cassette up.
(4) Close the cassette compartment by pressing
the mark on the cassette compartment.
The cassette compartment automatically goes
down.
(5) Close the lid of the cassette compartment.
2 3
To eject a cassette
Follow the procedure above, and eject the
cassette in step 3.
22
Пункт 1 Подготовка источника
питания
По индикатору времени оставшегося
заряда батарейного блока во время
записи
Если заряд израсходован, а индикатор
оставшегося заряда батарейного блока
показывает еще достаточный заряд для
его эксплуатации
Что такое "InfoLITHIUM"?
Пункт 2 Установка
кассеты
(1)
(2)
(3)
(4)
(5)
4,5
Для извлечения кассеты
3
Step 1 Preparing the power
supply
Connecting to the mains
When you use your camcorder for a long time,
we recommend that you power it from the mains
using the AC power adaptor.
(1) Open the DC IN jack cover, and connect the
AC power adaptor to the DC IN jack on your
camcorder with the plug's v mark facing up.
(2) Connect the mains lead to the AC power
adaptor.
(3) Connect the mains lead to the mains .
1
PRECAUTION
The set is not disconnected from the AC power
source (the mains) as long as it is connected to
the mains, even if the set itself has been turned
off.
Notes
•The AC power adaptor can supply power even
if the battery pack is attached to your
camcorder.
•The DC IN jack has "source priority". This
means that the battery pack cannot supply any
power if the mains lead is connected to the DC
IN jack, even when the mains lead is not
plugged into the mains.
Using a car battery
Use Sony DC Adaptor/Charger (not supplied).

Step 2 Inserting a cassette

Notes
•Do not press the cassette compartment down.
Doing so may cause malfunction.
•Your camcorder records pictures in the Digital8
system.
• The recording time when you use your
camcorder is half of indicated time on Hi8
tape. If you select the LP mode in the menu
settings, 3/4 of indicated time on Hi8
•If you use standard 8 tape, be sure to play
back the tape on this camcorder. Mosaic-pattern
noise may appear when you play back standard
8 tape on other camcorders (including other
DCR-TRV720E/TRV820E).
•The cassette compartment may not be closed
when you press any part of the lid other than
the mark.
•Do not pick up your camcorder by holding the
lid of the cassette compartment.
To prevent accidental erasure
Slide the write-protect tab on the cassette to
expose the red mark.
1-4
Пункт 1 Подготовка источника
питания
Подсоединение к сетевой
розетке
(1)
v
(2)
(3)
2, 3
ПРЕДОСТЕРЕЖЕНИЕ
Примечания
Использование автомобильного
аккумулятора
Пункт 2 Установка кассеты
Примечания
tape.
Для предотвращения случайного стирания
21
23