Sharp MX-M350 Service Manual page 224

66-43
Purpose Setting
Function PIC adjustment value writing (Only when FAX is
(Purpose) installed)
Section FAX
Item Operation
Operation/Procedure
To execute this simulation, FAX program writing must be allowed.
(Jumpers and DIP SW depending on the model.) The adjustment
values in PIC are changed or rewritten.
1) Enter the number corresponding to the set item with 10-key.
2) Press [START] key.
3) Enter the set value.
4) Press [P] key.
5) Select 0.
6) The confirmation window is displayed. Select whether the PIC
adjustment values are written or not.
YES The adjustment values are collectively written into PIC
installed in the FAX BOX.
NO No writing
When writing of the PIC adjustment values is normally completed,
"OK" is displayed. In case of an error, "NG" is displayed.
Item
0 WRITING for PIC Writing to PIC
1 ci_level_judge Number of sensing
until the CI signal
level is setteld.
2 ci_cycle_min CI signal cycle
min. Time
3 ci_cycle_max CI signal cycle
max. time
4 ci_range CI signal allowable
range
5 ci_count CI signal
settlement number
of times
6 ci_detect CID IN- signal
settlement number
of times
7 fnet_level_judge Sense number of
times until
settlement of
FNET signal level
8 fnet_range FNET signal
allowable range
9 fnet_time_out FNET time out
time
10 fnet_count FNET signal
settlement number
of times
11 poff_time PON signal OFF
time
12 mswon_level_judge Sense number of
times until
settlement of
MSW_ON signal
level
Content Set range Default
– –
1-15 2
0-254 10
0-254 107
0-127 5
1-15 3
1-15 8
1-15 1
0-74 3
76-255 100
1-15 3
0-15 3
2-15 3
MX-M350/M450 N/U SIMULATION 9 - 85
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
ENABLE WRITE PIN(for FAX PROGRAM ROM).
SELECT 0-12, AND PRESS START.
0.WRITING for PIC 1.ci_level_judge
2.ci_cycle_min 10 3.ci_cycle_max
5.ci_count 3 6.ci_detect
8.fnet_range 3 9.fnet_time_out
11.poff_time 3 12.mswon_level_judge
Select other then 0 , and
press [START] key.
Press [SYSTEM SETTINGS] key
or press [START] key.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING. INPUT VALUE 1-15, AND
PRESS START.
1.ci_level_judge(1-15)
Select 0
and press
[START] key.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
ARE YOU SURE ?
1.YES
2.NO
Select 1.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
EXECUTING...
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
OK ( or NG )
67
67-16
Purpose Operation test/Check
Function Used to check the operation of the network card.
(Purpose)
Section MFP controller
Item Operation
Operation/Procedure
During check, "CHECKING" is displayed. When check is com-
pleted normally, "OK" is displayed. In case of an error, "NG" is dis-
played.
(Display message)
CHECKING
OK
NG
SIMULATION 67-16
NETWORK INTERFACE CARD CHECK.
NIC: CHECKING
Check end Press [SYSTEM SETTINGS] key.
SIMULATION 67-16
NETWORK INTERFACE CARD CHECK.
NIC: OK (or NG)
1
2
107 4.ci_range
8 7.fnet_level_judge 1
100 10.fnet_count
3
2
Press [SYSTEM SETTINGS] key
or select 2.
1
Press [SYSTEM SETTINGS] key.
Interface/Communication
Checking
Check end (Normal)
Check end (Error)
5
3