Sharp MX-M350 Service Manual page 177

SIMULATION 46-10
EXP. LEVEL SETUP (MIX.2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. 1.0 50 4. 1.5 50
6. 2.5 50 7. 3.0 50
9. 4.0 50 10. 4.5
Select other than 0 - 2, and
press [START] key.
SIMULATION 46-10
EXP. LEVEL SETUP (MIX.2). INPUT VALUE 0-99, AND PRESS
START.
3. 1.0
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 46-10
EXP. LEVEL SETUP (MIX.2). NOW COPYING.
Select 0, and
press [START] key.
SIMULATION 46-10
EXP. LEVEL SETUP (MIX.2). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2
5. BPT
Select 2, and press [START] key.
SIMULATION 46-10
EXP. LEVEL SETUP (MIX.2). SELECT 3-11, AND PRESS START.
(EXP. LEVEL SELECT)
3. 1.0 4. 1.5
6. 2.5 7. 3.0
9. 4.0 10. 4.5
5. 2.0 50
8. 3.5 50
50 11. 5.0 50
Press [SYSTEM SETTINGS] key.
50
Press [SYSTEM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [SYSTEM SETTINGS] key.
3. TRAY3 4. TRAY4
Press [START] key, or
press [SYSTEM SETTINGS] key.
5. 2.0
8. 3.5
11. 5.0
MX-M350/M450 N/U SIMULATION 9 - 38
46-11
Purpose Adjustment
Function Used to adjust the print density for each density
1
(Purpose) level (display value) in the copy mode (binary -
Photo mode). An optional print density can be set
for each density level (display value).
Item Picture quality
Operation/Procedure
1) Select the number corresponding to the copy density adjust-
ment level with 10-key. (Select one of 3 - 11.)
2) Press [START] key.
3) Enter the copy density level with 10-key.
0 TRAY SELECT Paper feed tray selection
1 COPY START
2 EXP LEVEL
3 1.0
4 1.5
5 2.0
6 2.5
7 3.0
8 3.5
9 4.0
10 4.5
11 5.0
1
4) Press [P] key or [START] key.
The adjustment value is set.
When [START] key is pressed, copying is perfumed and the
adjustment value is set simultaneously.
Check the density of printed copy image.
Normal display
ERROR display
1
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
copying is performed.
Set
Item
range
Copy START (Default)
Exposure level selection
Exposure level 1.0 0 - 99
Exposure level 1.5
Exposure level 2.0
Exposure level 2.5
Exposure level 3.0
Exposure level 3.5
Exposure level 4.0
Exposure level 4.5
Exposure level 5.0
NOW COPYING.
Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
Density
Default
50