Sharp MX-M350 Service Manual page 185

46-20
Purpose Adjustment
Function Used to adjust the copy density correction in the
(Purpose) SPF copy mode for the document table copy
mode. The adjustment is made so that the copy
density becomes the same as that of the
document table copy mode.
Section SPF
Item Picture quality
Operation/Procedure
(Adjustment mode selection)
1) Select the number corresponding to the copy mode to be
adjusted with 10-key.
SPF odd pixel (Front surface copy), SPF even pixel (Front sur-
face copy), SPF (Back surface copy) (Select one of 3 - 5.)
2) Press [SATART] key.
(Copy density level adjustment)
1) Enter the density correction value with 10-key.
2) Press [P] key or [START] key.
(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
copying is performed.
Item
0 TRAY SELECT Paper feed tray selection
1: TRAY1
2: TRAY2
3: TRAY3
4: TRAY4
5: Manual feed
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3: Exposure level 1.0
4: Exposure level 1.5
5: Exposure level 2.0
6: Exposure level 2.5
7: Exposure level 3.0
8: Exposure level 3.5
9: Exposure level 4.0
10: Exposure level 4.5
11: Exposure level 5.0
3 SPF (ODD) SPF (front) (odd pixel)
4 SPF (EVEN) SPF (front) (even pixel)
5 DSPF DSPF (Back surface)
• "Set value - 128" is added to the shading adjustment value (SIM
46-17).
Density
Set
Content Default
range
–
–
–
0 - 255 128
MX-M350/M450 N/U SIMULATION 9 - 46
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 0-5, AND PRESS START.
0.TRAY SELECT
2.EXP LEVEL
3.SPF(ODD)
4.SPF(EVEN)
5.DSPF
Select other than 0 - 2, and press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS
START.
3.SPF(ODD)
Press [START] key.
Select 1,
and press
[START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT.
Select 0, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1
5.BPT
Select 2, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
3.1.0
6.2.5
9.4.0
46-21
Purpose Adjustment
– Function Used to adjust the scanner exposure level in all
(Purpose) the scanner modes.
Item Picture quality
Operation/Procedure
1) Select "SCANNER EXP. LEVEL" with 10-key.
2) Press [START] key.
–
3) Enter the image density adjustment value.
–
4) Press [P] key or [START] key.
NOTE: When this simulation is performed to adjust the scan image
densities, all the image densities in all the scan modes are
changed to the image density level set with this simulation.
That is, the image densities set with SIM 46-22, 23, 24, 25,
and 45 are changed to the image density level set with this
simulation.
0 SCANNER EXP. LEVEL Image density level 0 - 99
NOTE: Only the set value is changed and no printing is performed.
1 1.PRINT START
1
128
128
128
Press [SYSTEM SETTINGS] key.
Press [SYSTEM SETTINGS] key,
or terminate copying.
NOW PRINTING.
Press [START] key or
press [SYSTEM SETTINGS] key.
2.TRAY2 3.TRAY3 4.TRAY4
Press [START] key or
press [SYSTEM SETTINGS] key.
4.1.5 5.2.0
7.3.0 8.3.5
10.4.5 11.5.0
Item
1
128
1
1
Density
Set
Default
range
50