Sharp MX-M350 Service Manual page 178

SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. 1.0 50 4. 1.5 50
6. 2.5 50 7. 3.0 50
9. 4.0 50 10. 4.5
Select other than 0 - 2, and
press [START] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). INPUT VALUE 0-99, AND PRESS
START.
3. 1.0
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). NOW COPYING.
Select 0, and
press [START] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2
5. BPT
Select 2, and press [START] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). SELECT 3-11, AND PRESS START.
(EXP. LEVEL SELECT)
3. 1.0 4. 1.5
6. 2.5 7. 3.0
9. 4.0 10. 4.5
46-12
Purpose Adjustment
Function Used to adjust the print density in the FAX mode
(Purpose) (all modes).
Item Picture quality
Operation/Procedure
1) Select the adjustment item of FAX EXP. LEVEL with 10-key.
2) Press [START] key.
3) Enter the print density level with 10-key.
Item
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 FAX EXP. LEVEL FAX mode print density
5. 2.0 50
8. 3.5 50
50 11. 5.0 50
Press [SYSTEM SETTINGS] key.
50
Press [SYSTEM SETTINGS] key,
or terminate copying.
Press [START] key,
or press [SYSTEM SETTINGS] key.
3. TRAY3 4. TRAY4
Press [START] key, or
press [SYSTEM SETTINGS] key.
5. 2.0
8. 3.5
11. 5.0
Set
Default
range
0 - 99
MX-M350/M450 N/U SIMULATION 9 - 39
4) Press [P] key or [START] key.
The adjustment value is set.
When [START] key is pressed, printing is perfumed and the
adjustment value is set simultaneously.
1
Check the density of printed image.
Normal display
ERROR display
NOTE: When the FAX print image density is adjusted with this sim-
ulation, the print image densities of all the FAX modes are
changed to the image density level set with this simulation.
That is, the print image density of each FAX mode set with
SIM 46-13, 14, 15 is changed to the print image density
level adjusted with this simulation.
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
1
4 TRAY4
5 BPT
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
copying is performed.
SIMULATION 46-12
1
EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS
START.
0.TRAY SELECT
2.FAX EXP.LEVEL
Select other than 0 - 1, and
press [START] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND
PRESS START.
2.FAX EXP.LEVEL
Select 1, and
Press [START] key.
press [START] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET). NOW PRINTING.
50
Select 0, and
press [START] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
NOW PRINTING.
Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
1 1.COPY START
50
Press [SYSTEM SETTINGS] key.
Press [SYSTEM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [SYSTEM SETTINGS] key.
1
50