Sharp MX-M350 Service Manual page 191

SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
3.CCD(MAIN) 50 4.CCD(SUB)
5.SPF(MAIN) 50 6.SPF(SUB)
Select other than 0 - 2,
and press [START] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
4.CCD(SUB)
Press [START] key.
Select 1, and
press [START] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. NOW COPYING.
Select 0, and press [START] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Select 2, and
press [START] key.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
48-5
Purpose Adjustment
Function Used to adjust the copy magnification ratio in the
(Purpose) sub scanning direction.
Section Optical (Image scanning)
Item Picture quality
Operation/Procedure
When the sub scanning direction image magnification ratio adjust-
ment with SIM 48-1 cannot provide a satisfactory result if a differ-
ent magnification ration is set and a copy is made, perform this
simulation.
When there is an error in the copy magnification ratio in reduction
copy, change the adjustment value of the high speed mode. When
there is an error in the copy magnification ratio in enlargement
copy, change the adjustment value of the low speed mode.
1) Select the number corresponding to the adjustment mode with
10-key.
2) Press [START] key.
3) Enter the copy adjustment value with 10-key.
The scanner/SPF motor rotation sped adjustment value is
entered.
Item Content
0 MIR (220) Mirror motor (220mm/sec)
1 MIR (169) Mirror motor (168.7mm/sec)
2 MIR (110) Mirror motor (110mm/sec)
3 MIR (55) Mirror motor (55mm/sec)
4 SPF (220) SPF motor (220mm/sec)
5 SPF (110) SPF motor (110mm/sec)
2
50
50 7.CIS(MAIN) 50
Press [SYSTEM SETTINGS] key.
50
Press [SYSTEM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [SYSTEM SETTINGS] key.
1
Press [START] key, or
press [SYSTEM SETTINGS] key.
100
Set
Default
range
0 - 99 50
MX-M350/M450 N/U SIMULATION 9 - 52
4) Press [START] key.
SIMULATION 48-5
MOTOR SPEED ADJUSTMENT. SELECT 0-5, AND PRESS START.
0.MIR(220) 50 1.MIR(169)
2.MIR(110) 50 3.MIR(55)
4.SPF(220) 50 5.SPF(110)
Select other than 0 - 5, and
press [START] key.
SIMULATION 48-5
SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
0.MIR(220)
48-6
Purpose Adjustment
Function HSYNC cycle adjustment
(Purpose)
Item Picture quality
Operation/Procedure
(Adjustment mode selection)
1) Select the number corresponding to the HSYNC cycle to be
adjusted with 10-key. (Select one of 3.)
2) Press [START] key.
Item
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 MAGNIFICATION Print magnification ratio
3 CIS CIS HSYNC cycle
(HSYNC cycle adjustment)
1) Select the number corresponding to the HSYNC cycle to be
adjusted with 10-key. (Select one of 3.)
2) Press [START] key.
3) Enter the HSYNC cycle adjustment value with 10-key.
4) Press [START] key.
When the [START] key is pressed, copying is performed and
the adjustment value is set simultaneously.
Normal display
ERROR display Door open
Jam
Paper empty
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
selected paper with 10-key. (Select one of 1 - 5.)
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex mode.
50
0
50
50
Press [START] key, or
press [SYSTEM SETTINGS] key.
50
Set
Default
range
– –
– –
25 - 400 –
40 - 60 50
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed