Wireless Control Setting; Fixture Setting - ProLights Reflex User Manual

3.10 WIRELESS CONTROL SETTING

(For the unit with wireless receiver built-in only)
• Press MENU to select [DMX FUNCTIONS] and press ENTER button to confirm.
• Select [WDMX Setting], press ENTER button to confirm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to confirm the set-
ting.
- [Active] - Wireless control. Select [Active], press ENTER button to confirm, use UP/DOWN button to
select [Yes] (wireless control available) or [No] (wireless control unavailable), press ENTER button to
store.
- [Retransmit] - Select [Retransmit], press ENTER button to confirm, use UP/DOWN button to select [Yes]
or [No], press ENTER button to store.
- [Reset Memory] - Refuse wireless signal. Select [Reset Memory], press ENTER button to confirm, use UP/
DOWN button to select [Yes] (refuse wireless signal) or [No], press ENTER button to store.
- [WDMX Channel] - Select [WDMX Channel], press ENTER button to confirm, use UP/DOWN button to adjust
the channel (000~015).
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

3.11 FIXTURE SETTING

It is possible to change the device parameter values in the following way.
• Press MENU to select [FIXTURE SETTING] and press ENTER button to confirm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to confirm the set-
ting.
- [Pan Inverse] - Used for reversing Pan movement. Select [Pan Inverse], press ENTER button to confirm,
present mode will blink on the display, use UP/DOWN button to select [No] (normal) or [Yes] (pan
inverse), press ENTER button to store.
- [Tilt Inverse] - Used for reversing tilt movement. Select [Tilt Inverse], press ENTER button to confirm,
present mode will blink on the display, use UP/DOWN button to select [No] (normal) or [Yes] (tilt
inverse), press ENTER button to store.
- [P/T Feedback] - Select [P/T Feedback], press ENTER button to confirm, present mode will blink on the
display, press UP/DOWN button to select [No] (Pan or tilt's position will not feedback while out of
step) or [Yes] (Feedback while pan/tilt out of step), press ENTER button to store.
- [BL.O. P/T Moving] - Blackout while Pan/Tilt moving. Select [BL.O. P/T Moving] press ENTER button to
confirm, present mode will blink on the display, use UP/DOWN button to select [No] (normal while
pan/tilt moving) or [Yes] (blackout while pan/tilt moving), press ENTER button to store.
- [White Balance] - Select [White Balance], press ENTER button to confirm, present mode will blink on the
display, use UP/DOWN button to select Red, Green or Blue. Once selected, press ENTER button, then
use UP/DOWN button to adjust the value from 125 to 255, press ENTER button to store.
- [Cool Mode] - Select [Cooling Mode], press ENTER button to confirm, present mode will blink on the
display, use UP/DOWN button to select [Auto] (Normal) or [Low] (Low speed), Once selected, press
ENTER button to store.
- [Dimmer Curve] - Select [Dimmer Curve], press ENTER button to confirm, present mode will blink on the
display, use UP/DOWN button to select Linear, Square Law, Inverse Squ. or S-curve, Once selected,
press ENTER button to store.
• [Linear]: The increase in light intensity appears to be linear as DMX value is increased.
• [Square Law]: Light intensity control is finer at low levels and coarser at high levels.
• [Inverse Square Law]: Light intensity control is coarser at low levels and finger at high levels.
• [S-cure]: Light intensity control is finger at low levels and high levels and coarser at medium levels.
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.
REFLEX
15