System Answer Mode; Do Not Disturb Mode - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
"One Short Beep". Refer to
Chapter 5 System's Operation.
Step5
to program another parameter
otherwise press ∗ to exit and you will
hear "Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
96 Code (factory default is 0000) and you
will hear "One Short Beep". If you
SYSTEM
entered an invalid master code you will
ANSWER MODE
hear "One Long Beep", repeat
step 1. Should your master code
ENABLE OR
become lost or forgotten see Reset
DISABLE THE
Master Code.
AUTO ANSWER
MODE. IF
DISABLE THE
Step 3
SYSTEM WILL
hear "One Short Beep".
NOT ANSWER
AN INCOMING
Step 4
CALL FROM THE
disabled) or 1, 2, 3 or....9 (system will
OUTSIDE LINE.
answer a remote call on 1 st ring, 2 nd
ring, 3 rd ring...9 th ring) then press #
and you will hear "One Short Beep".
Step 5
to program another parameter
otherwise press ∗ to exit and you will
hear "Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
hear "One Long Beep", repeat
97
step 1. Should your master code
become lost or forgotten see Reset
DO NOT
Master Code.
DISTURB MODE
Step 3
DISABLE OR
hear "One Short Beep".
ENABLE THE
SYSTEM TO
CALL
Step 4
0 to disable Do not Disturb Mode
(mode 0 is factory default setting)
1 to enable Do not Disturb Mode
(system will not call to a premise or
remote location)
then press #, you will hear "One Short
Beep".
Step 5
to program another parameter
otherwise press ∗ to exit and you will
Pach and Company
AeGIS 4000
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Enter 96 then #, you will
Enter 0 (system answer is
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Enter 97 then #, you will
Enter
Enter another Function Code
Premise Phone
The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 97
then press #, you will hear "One Short
Beep".
Step 5 Enter 0 (to disable) or 1 (to
enable) then press #, you will hear
"One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three
Short Beeps".
Page 19
Chapter 3. Programming
Remote Phone
Step 5 Enter another function
code to program a different parameter
or exit the program by pressing ∗ ∗
and you will hear "Three Short
Beeps".
The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel.
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 97
then press #, you will hear "One Short
Beep".
Step 4 Enter 0 (to disable) or 1 (to
enable) then press #, you will hear
"One Short Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".