Select Initiating Premise Call Key; Set Memory To Factory Default - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
hear "Three Short Beep".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
98
hear "One Long Beep", repeat
step 1. Should your master code
SELECT
become lost or forgotten see Reset
INITIATING
PREMISE CALL Master Code.
KEY
## or **
Step 3
hear "One Short Beep".
Step 4
use ∗ ∗ ∗ ∗ then press #, you will hear
"One Short Beep".
Step 5
to program another parameter other-
wise press ∗ to exit and you will hear
"Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
99
will hear "One Short Beep". If you
entered an invalid master code you will
SET MEMORY
hear "One Long Beep", repeat
TO FACTORY
step 1. Should your master code
DEFAULT
become lost or forgotten see Reset
Master Code.
ERASE THE
MEMORY AND
Step 3
RESET THE
hear "Two Long Beeps".
SYSTEM TO
FACTORY
Step 4
DEFAULT, THE
MASTER CODE
you will hear "One shor
IS ALSO RESET
then # to clear the system's database
TO 0000
and entire configuration to factory
default and you will hear "Three short
beeps".
Step 5
to program another parameter
otherwise press ∗ to exit and you will
hear "Three Short Beeps".
Pach and Company
AeGIS 4000
Entering The Programming
Enter the 4-digit Master
Enter 98 then #, you will
Enter 0 to use # key or 1 to
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Enter 99 then #, you will
Enter 0 then # to cancel and
t
beep" or 1
Enter another Function Code
Premise Phone
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 98
then press #, you will hear "One Short
Beep".
Step 5 Enter
0 = to select ## or
1 = to select ∗∗
then press #, you will hear "One Short
Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
It must be done locally at the
main lobby control panel.
Page 20
Chapter 3. Programming
Remote Phone
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 98
then press #, you will hear "One Short
Beep".
Step 4 Enter 0 (to select ##) or 1 (to
select ∗∗) then press #, you will hear
"One Short Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
It must be done locally at the
main lobby control panel.