Program Individual Access Code - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
Step 3
hear "No Beep".
Step 4
Code then press # then you will hear
"One Short Beep" and proceed to
step 5 or if you decided
not to change the existing Master
Code press ∗ to exit and you will hear
"Three Short Beeps".
Step 5
parameter or press ∗ to exit; you will
hear "Three Short Beeps".
Program
Step 1
Individual
Mode: Press 0 and # simultaneously
Access Code
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
hear "One Long Beep", repeat
step 1. Should your master code
become lost or forgotten see section
Reset Master Code.
01-20
Step 3
INDIVIDUAL
(01 – 20, 21-40 or 41-50) then #, you
ACCESS CODE
will hear "No Beep". If the associated
TO ACCESS
Index Number has an access code
RELAY 1
programmed, you will hear "Two Long
(DOOR 1)
Beeps". Press ∗, you will hear "One
Short Beep" and select another Index
21-40
Number.
INDIVIDUAL
ACCESS CODE
Step 4
TO ACCESS
code then #, you will hear "One
RELAY 2
Beep".
(DOOR 2)
Do not program the same code as in
index01-20, 21-40 and 41-50, doing
41-50
so the access code programmed
won't work.
INDIVIDUAL
ACCESS CODE
TO ACCESS
Step 5
BOTH RELAY 1
another access code or enter another
AND 2 (DOOR 1
Function Code to program another
AND DOOR 2)
parameter, otherwise
press ∗ to exit and you will hear
"Three Short Beeps
Pach and Company
AeGIS 4000
Enter 00 then #, you will
Enter new 4-digit Master
Continue to program another
Entering The Programming
Enter the 4-digit Master
Enter the Index Number
Enter the 4-digit access
Return to step 3 to program
Premise Phone
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the 01-20, 20-21 or
41-50) then press #, you will hear "No
Beep": the index numbers is empty
and proceed to Step 5. "Two Long
Beeps": the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear "No
Beep" to overwrite existing access
code and proceed to Step 4.
• Press ∗ ∗ you will "One Short Beep"
and repeat this step.
Step 5 Enter the 4-digit access
code number then press #, you will
hear "One Short Beep".
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won't work.
Step 6 Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing ∗ ∗ and you will
hear "Three Short Beeps".
Page 9
Chapter 3. Programming
Remote Phone
Step 1 Call to the AeGIS 4000 sys-
tem (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep" .
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
"One Short Beep" or ∗∗ to hang-up
the call.
Step 4 Enter the 01-20, 21-40, or
41-50then press #, you will hear "No
Beep": the index numbers is empty
and proceed to Step 5. "Two Long
Beeps": the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear "No
Beep" to overwrite existing access
code and proceed to Step 4.
• Press ∗ ∗ you will "One Short Beep"
and repeat this step.
Step 5
Enter the 4-digit access
code number then press #, you will
hear "One Short Beep".
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won't work.
Step 6
Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing ∗ ∗ and you will
hear "Three Short Beeps".