Delete All Call Forwarding; Enable Or Disable Automatic Call Forwarding - PACH & COMPANY AeGIS 4000 Installation And Programming Manual

Function Local Programming
"One Short Beep" and select another
Function Number (71 – 72).
Step 4
• Enter 0 then #, you will hear "One
Short Beep" and phone number
programmed is deleted or
• Enter 1 then #, you will hear "No
Beep" and enter a new call
forwarding phone number up to
11- digit, you will hear "One Short
Beep".
Step 5
to delete another Call Forwarding or to
program another parameter otherwise
press ∗ to exit and you will hear
"Three Short Beeps".
Entering The Programming Mode:
Press 0 and # simultaneously then
release. If you are in the programming
mode, proceed to step 2.
Step 2
Code (factory default is 0000) and you
will hear "One Short Beep". If you
entered an invalid master code you will
76
hear "One Long Beep", repeat
DELETE ALL
step 1. Should your master code
CALL
become lost or forgotten see Reset
FORWARDING
Master Code.
PHONE
NUMBER ON
Step 3
FUNCTION
hear "One Short Beep".
CODE 70, 71 and
72
Step 4
to program another parameter
otherwise press ∗ to exit and you will
hear "Three Short Beeps".
Step 1
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2
87
Code (factory default is 0000) and you
will hear "One Short Beep". If you
ENABLE OR
entered an invalid master code you will
DISABLE
AUTOMATIC hear "One Long Beep", repeat
CALL
step 1. Should your master code
FORWARDING
become lost or forgotten see Reset
Master Code.
Pach and Company
AeGIS 4000
Enter another Function Code
Enter the 4-digit Master
Enter 76 then #, you will
Enter another Function Code
Entering The Programming
Enter the 4-digit Master
Premise Phone
Step 5
•
Press "0" and #, you will hear "One
Short Beep" and phone number
programmed is deleted or
• Press "1" then press # you will hear
"No Beep" and enter a new phone
number up to 11-digit then press #,
you will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps"
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Enter the Function Code 76
then press #, you will hear "One Short
Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
"One Short Beep".
Step 3 Press # and you will hear
"One Short Beep".
Step 4 Press 87 then #, you will
hear "One Short Beep".
Page 14
Chapter 3. Programming
Remote Phone
Step 4 Enter the Function Code
number "71" or "72" then press #, you
will hear "Two Long Beeps"; means a
phone number is already programmed,
proceed to step 5. If you hear "No
Beep", means no phone number is
programmed, press ∗ and continue
step 4 or proceed to step 6.
Step 5
• Press "0" and #, you will hear "One
Short Beep" and phone number is
deleted.
.
• Press "1" then press # you will hear
"No Beep" and enter a new phone
number up to 11-digit then press #,
you will hear "One Short Beep".
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and yo
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
"One Short Beep" or ∗∗ to hang-up
the call.
Step 4 Enter the Function Code 76
then press #, you will hear "One Short
Beep".
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing ∗ ∗ and
you will hear "Three Short Beeps".
Step 1 Call to the AeGIS 4000
system (you must know the system's
phone number), you will hear: "One
Short Beep", the gate is locked. "Two
Short Beeps", the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• "One Short Beep", the master code
is accepted then press # and you will
hear "One Short Beep".
• "One Long Beep", the master code
is rejected and the connection will be
disconnected.
u
will