Set Memory to Factory Default ........................20 CHAPTER 4. OPERATION .............................. 21 To Initiate the Call and Disconnect the Call from the AeGIS 4000 ..............21 Answer the AeGIS 4000 Call and Extend the Talk Time ................. 21 Provide Access to Visitor ..........................21 Using A Call Waiting Feature ...........................
Pach and Company does not assume any liability for any damages, which may arise in installation or use of the AeGIS 4000 Series. Pach and Company does not assume liability for any incompatibility between the AeGIS 4000 Series and users devices.
Pach & Company thanks and congratulates you on the purchase of your AeGIS 4000 Series Telephone Access Control System. This manual is designed to guide you through the proper programming and use of the AeGIS 4000 Series. It is important for you to read and follow the manual completely.
Check the serial number on the printed circuit board, cabinet and warranty card, they must match. If they do not match, please contact Pach and Company toll free number at (888) 678-7224. All the items listed below come with the AeGIS 4000 Series.
NEW PRODUCT WARRANTY EXCEPTION WIEGAND CARD, KEYFOB AND TRANSMITTER Pach and Company Page 3 AeGIS 4000 Chapter 1. Getting Started...
Page 10
Pach and Company warrants the wiegand card, clam, and keyfob to be free of defects in material or workmanship for a period of three (3) months from the date of invoice. The above warranty is subject to the following conditions. 1.
Page 11
4. Under no circumstances will Pach and Company honor warranty any product found to have been altered, repaired, and/or modified by the end-user consumer. 5. Pach and Company reserves the right to replace a warranted product with a like product of equal value in the event original system cannot be repaired.
Page 12
9. Pach and Company warranty does not guarantee any product, new or repaired, to be free of operation error or service interruption in any way during the course of daily product operation 10. Pach and Company is not responsible for time, travel, and/or labor costs of any distributor and/or dealer-installer, including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty issues, product enhancements, or product failures.
CHAPTER 2. INST ALLA TION A proper installation of the AeGIS system is very essential. You MUST follow the installation-wiring steps as shown in figure Figure 2.1 Single System Wiring Diagram Pach and Company Page 4 AeGIS 4000 Chapter 2. Installation...
Page 14
Pach and Company Page 5 AeGIS 4000 Chapter 2. Installation...
Page 15
Warning: Longer distance with bigger gauge wires is not recommended. Do not connect Phone Central Office to Home Phone Terminal. NOTE: If you install the AeGIS 4000 on dedicated phone for call forwarding only, do not do this step, return to step2.
Page 16
Step 8 POWER. ONLY use a Class 2 transformer rated 12 VAC 20VA (supplied) or 12 VDC 20 VA to power the AeGIS 4000. Optional 12 VDC 4Ahr battery back up with built-in charger can be installed as shown in figure 2.2. The output volt- age of the battery and charger must be between 13.5 VDC - 15 VDC, lower than 13.5 VDC will cause the on...
CHAPTER 3. PROGRAMMING The AeGIS 4000 can be programmed Local (using built-in keypad), Premise Phone or Remote Phone. Premise phone programming can only be used if the existing Central Office Line is connected to the system as shown in figure 2.1.
∗ to exit; you will hear “Three Short Beeps”. Program Step 1 Pick up the phone and wait Step 1 Call to the AeGIS 4000 sys- Step 1 Entering The Programming Individual for dial tone. tem (you must know the system’s...
∗ to exit and you will hear “Three Short Beeps”. Pick up the phone and wait for a dial Step 1 Call to the AeGIS 4000 Step 1 Entering The Programming tone. system (you must know the system’s Mode: Press 0 and # simultaneously phone number), you will hear: “One...
Step 1 Entering The Programming Pick up the phone and wait for a dial Step 1 Call to the AeGIS 4000 Mode: Press 0 and # simultaneously tone. system (you must know the system’s then release. If you are in the phone number), you will hear: “One...
Short Beeps”, the gate is unlocked. “One Short Beep”. “Three Short Beeps”. Now, the AeGIS 4000 is reset to “Intercom Step 2 Press # then enter a valid Step 3 Press 6 and you will hear Mode”.
∗ ∗ and you will hear “Three Short Beeps”. Delete or Step 1 Pick up the phone and wait Call to the AeGIS 4000 system (you Step 1 Entering The Programming Rewrite for a dial tone.
∗ ∗ and you will hear “Three Short Beeps”. Step 1 Call to the AeGIS 4000 Entering The Programming Mode: Step 1 Pick up the phone and wait system (you must know the system’s Press 0 and # simultaneously then for a dial tone.
Entering The Programming Step 1 Pick up the phone and wait Step 1 Call to the AeGIS 4000 Mode: Press 0 and # simultaneously for a dial tone. system (you must know the system’s then release. If you are in the pro- phone number), you will hear: “One...
Entering The Programming Step 1 Pick up the phone and wait Step 1 Call to the AeGIS 4000 Mode: Press 0 and # simultaneously for a dial tone. system (you must know the system’s then release. If you are in the phone number), you will hear: “One...
Entering The Programming Step 1 Pick up the phone and wait Step 1 Call to the AeGIS 4000 Mode: Press 0 and # simultaneously for a dial tone. system (you must know the system’s then release. If you are in the phone number), you will hear: “One...
Pick up the phone and wait Step 1 Entering The Programming Step 1 Call to the AeGIS 4000 for a dial tone. Mode: Press 0 and # simultaneously system (you must know the system’s then release. If you are in the pro- phone number), you will hear: “One...
∗ to exit and you will hear “Three Short Beeps”. Step 1 Pick up the phone and wait Step 1 Call to the AeGIS 4000 Step 1 Entering The Programming for a dial tone. system (you must know the system’s Mode: Press 0 and # simultaneously phone number), you will hear: “One...
Remote Phone hear “Three Short Beep”. Step 1 Entering The Programming Step 1 Call to the AeGIS 4000 Step 1 Pick up the phone and wait Mode: Press 0 and # simultaneously system (you must know the system’s for a dial tone.
(door 1) or press 8 to provide access to relay 2 (door 2) to visitor and you will hear “Two Short Beeps”. USING A CALL WAITING The AeGIS 4000 has built-in call waiting feature. You may not be able to tell the different FEATURE. between the AeGIS call waiting beeps and the phone company call waiting beeps.
Short Beep”. If you hear “One Short Beep”, means the door is unlocked or Press 0 (to lock) then press #, you will hear “One Long Beep” then “One Short Beep. Pach and Company Page 22 AeGIS 4000 Chapter 4. Operations...
Press ∗ and now you are ready to talk to the AeGIS system. You may press 9 to Step 3 open door or gate. From Remote Location Step 1 Pick-up the handset and wait for dial tone. Pach and Company Page 23 AeGIS 4000 Chapter 4. Operations...
AeGIS system or remote (calling into a premise or remote location phone). Refer Function Code 95. Mode 0: the AeGIS 4000 will beep every second for 30 seconds and the system cannot be used for 60 seconds.
• If this is a new installation, remove the connection with the home phone and substitute with a telephone test set. • If this is an existing installation Call Pach and Company Technical Support Department. Pach and Company Page 25 AeGIS 4000 Chapter 5. Trouble Shooting Guides...
• The red dots along the ribbon cable must be facing up. 4-DIGIT ACCESS CODE DOES. • Turn the power OFF and disconnect the keypad’s ribbon cable from the board and reconnect it then turn the power ON. Pach and Company Page 26 AeGIS 4000 Chapter 5. Trouble Shooting Guides...
Relay 1 or Door 1 4-digit Relay 2 or Door 2 4-digit Relay 1 and 2 4-digit Call Forwarding Phone Numbers Function Code Phone Number Function Code Phone Number Pach and Company Page 27 AeGIS 4000 Chapter 5. Trouble Shooting Guides...
71-72 Auto or manual call forwarding phone number up to 11-digit. Must be enabled. SYSTEM OPERATION 1. To place a call from the AeGIS 4000: Press #. LOCAL PREMISE PHONE REMOTE PHONE 2. To grant access to a visitor: Press 9 (door 1) or 1.Press 0 and #...