Korg Pa50 User Manual page 195

Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: Control Mode, e: Voice1: Resonance, h: Voice2:
Resonance
This parameter determines the resonance intensity.
When "Control Mode" = Manual, the "Resonance"
parameter sets the intensity of resonance. If the "Reso-
nance" parameter has a negative value, harmonics will be
changed, and resonance will occur at a pitch one octave
lower.
When "Control Mode" = LFO, the intensity of resonance
varies according to the LFO. The LFO sways between posi-
tive and negative values, causing resonance to occur
between specified pitches an octave apart in turn.
When "Control Mode" = D-mod, the resonance is con-
trolled by the dynamic modulation source. If JS X or Rib-
bon is assigned as the modulation source, the pitch an
octave higher and lower can be controlled, similar to
when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When "Control Mode" = LFO or D-mod, the controlled
phase of either Voice 1 or 2 will be reversed. When the
resonance pitch is set for Voice 1 (Resonance has a positive
value), Voice 2 will resonate at a pitch an octave below
(Resonance has a negative value).
d: Voice1: Pitch, d: Fine [cent], g: Voice2: Pitch, g: Fine
[cent]
The Pitch parameter specifies the pitch of resonance by
note name. The "Fine" parameter allows for fine adjust-
ment in steps of cents.
e: High Damp [%], h: High Damp [%]
This parameter sets the damping amount of resonant
sound in the high range. Lower values will make a metal-
lic sound with a higher range of harmonics.
030: Doppler
This effect simulates the "Doppler effect" of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Doppler
Right
LFO
D -mod
Trigger LFO Mode = 1-Shot
LFO Mode
Switches LFO operation mode
a
Src
When LFO Mode is set to 1-Shot, this modulation source triggers the LFO
LFO Sync
b
Switches between LFO reset on and off when LFO Mode is set to Loop
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
d
e
g
a: LFO Mode, a: Src, b: LFO Sync
The "LFO Mode" parameter switches LFO operation
mode. When Loop is selected, the Doppler effect will be
created repeatedly. If "LFO Sync" is set to On, the LFO will
be reset when the modulation source specified with the
"Src" parameter is turned on.
When "LFO Mode" is set to 1-Shot, the Doppler effect is
created only once when the modulation source specified
in the "Src" field is turned on. At this time if you do not
set the "Src" parameter, the Doppler effect will not be
created, and no effect sound will be output.
Wet / Dry
e: Pitch Depth
With the Doppler effect, the pitch is raised when the
sound approaches, and the pitch is lowered when the
Pan Depth
sound goes away. This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the
Wet / Dry
effect sound. With larger values, the sound seems to come
and go from much further away. With positive values, the
sound moves from left to right; with negative values, the
sound moves from right to left.
Loop, 1-Shot
,
Off...Tempo
Off, On
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Pitch Depth
Sets the pitch variation of the moving sound
Src
Selects the modulation source of pitch variation
Amt
Sets the modulation amount of pitch variation
Pan Depth
Sets the panning of the moving sound
Src
f
Selects the modulation source of panning
Amt
Sets the modulation amount of panning
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
The effect is off when a value for the modulation source speci-
fied for the "Src" parameter is smaller than 64, and the effect is
on when the value is 64 or higher. The Doppler effect is trig-
gered when the value changes from 63 or smaller to 64 or
higher.
Pitch
Pan Depth
= (+) value
Original Pitch
Left
Pan Depth
< < < < < <<<<<< >>>>>> > >
Louder
Effects 193
Pitch/Phase Mod.
0.02...20.00Hz
Fx:009,
Off...Tempo
–20.00...+20.00Hz
Off, On
Fx:009,
MIDI, 40...240
Fx:009
Fx:009
x1...x16
Fx:009
0...100
,
Off...Tempo
–100...+100
–100...+100
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Doppler - Pitch / Pan Depth
Pan Depth
= (–) value
Pitch Depth
Center
Right
> > >
Volume Louder