Korg Pa50 User Manual page 191

The "Src" parameter selects the source that starts the
envelope generator. If you select, for example, Gate, the
envelope generator will start when the note-on message
is received.
When "Sweep Mode" = D-mod, the modulation source
can control the flanger directly. Select the modulation
source using the "Src" parameter.
The effect is off when a value for the modulation source speci-
fied for the "Src" parameter is smaller than 64, and the effect is
on when the value is 64 or higher. The Envelope Generator is
triggered when the value changes from 63 or smaller to 64 or
higher.
d: EG Attack, d: EG Decay
Attack and Decay speed are the only adjustable parame-
ters on this EG.
023: Phaser
(Stereo Phaser)
This effect creates a swell by shifting the phase. It is very
effective on electric piano sounds. You can add spread to the
sound by offsetting the phase of the left and right LFOs from
each other.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sine LFO Shape
LFO Waveform
Selects LFO Waveform
a
LFO Shape
Determines how much the LFO waveform is changed
LFO Phase [degree]
b
Sets the LFO phase difference between the left and right
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
Wet / Dry
Phaser
Resonance
High Damp
Phaser
Wet / Dry
LFO Phase
Triangle, Sine
–100...+100
Fx:020
–180...+180
Fx:010
0.02...20.00Hz
Fx:009,
Off...Tempo
–20.00...+20.00Hz
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
d
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Manual
e
Sets the frequency to which the effect is applied
Depth
Sets the depth of LFO modulation
Src
f
Selects the modulation source for the LFO modulation depth
Amt
Sets the modulation amount of the LFO modulation depth
Resonance
Sets the resonance amount
g
High Damp [%]
Sets the resonance damping amount in the high range
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
h
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
g: Resonance, h: Wet/Dry
The peak shape of the positive and negative Feedback
value is different. The harmonics will be emphasized
when the effect sound is mixed with the dry sound, if you
set a positive value for both "Resonance" and "Wet/Dry",
and if you set a negative value for both "Resonance" and
"Wet/Dry".
g: High Damp [%]
This parameter sets the amount of damping of the reso-
nance in the high range. Increasing the value will cut
high-range harmonics.
Effects 189
Pitch/Phase Mod.
Off, On
Fx:009,
MIDI, 40...240
Fx:009
Fx:009
x1...x16
Fx:009
0...100
0...100
Off...Tempo
–100...+100
–100...+100
0...100%
–Wet...–1:99, Dry, 1:99...Wet
Fx:010,
Off...Tempo
–100...+100