Korg Pa50 User Manual page 180

178 Effects
Filter/Dynamic
005: Gate
(Stereo Gate)
This effect mutes the input signal if its level is lower than the
specified level. It also reverses the on and off operation of the
gate, and uses Note On and Off messages to turn the gate on
and off.
Stereo In - Stereo Out
Left
Envelope - Control
+
Envelope - Control
Envelope Select
Right
Gate+Sus
Envelope Select
Selects from Control via the modulation source, mixing the left and right sig-
nals, Only left, and Only right
a
Src
Selects the modulation source that controls the gate when Envelope Select =
D-mod
Polarity
b
Switches between non-reversed and reversed Gate on/off
Threshold
c
Sets the level to which the Gate is applied
Attack
Sets the attack time
d
Release
Sets the release time
Delay Time [msec]
e
Sets the delay time of the gate input
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
f
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: Envelope Select, a: Src
The "Envelope Select" parameter selects whether the
gate on/off is triggered by the level of the input signal, or
controlled directly by the modulation source. The Src
parameter specifies the modulation source, selected from
Off to Gate2+Dpmr.
With "Envelope Select" = L/R Mix, the left and right chan-
nel signal mixture will trigger the gate on/off. When L
Only or R Only is selected, the gate is controlled by either
of the channel signals.
b: Polarity
This parameter reverses the Gate on/off operation. With a
negative value, the gate is closed when the input signal
level exceeds the Threshold. The gate operation con-
trolled by the modulation source is also reversed.
c: Threshold, d: Attack, d: Release
This parameter sets the signal level below which Gate is
applied when "Envelope Select" is set to L/R Mix, L Only,
or R Only.
Wet / Dry
Delay Gate
Delay Gate
Wet / Dry
D-mod, L/R Mix, L Only, R Only
,
Off...Gate2+Dmpr
+, –
0...100msec
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
The Attack and Release parameters set the Gate attack
time and release time.
Output Level
Dry
Wet
Wet
e: Delay Time
This parameter sets the delay time of the Gate input. If
the sound has a very fast attack, increase the delay time so
that the signal will be input after the Gate is opened. This
0...100
will preserve the attack part of the sound.
1...100
006: OD/HGainWah
1...100
(Overdrive/Hi.Gain Wah)
This distortion effect utilizes an Overdrive mode and a Hi-
Gain mode. Controlling the wah effect, the 3-band EQ, and
the amp simulation will allow you to create versatile distor-
tion sounds. This effect is suitable for guitar and organ
sounds.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Pre Low-cut
+
Right
D -mod
Wah
Switches Wah on/off
Src
a Selects the modulation source that switches the Wah on and off
Sw
Selects the switching mode for the modulation source that switches the Wah
on and off
Wah Sweep Range
Sets the range of Wah
b
Wah Sweep Src
Selects the modulation source that controls the Wah
Drive Mode
c
Switches between overdrive and hi-gain distortion
Drive
Sets the degree of distortion
d
Pre Low-cut
Sets the low range cut amount of the distortion input
Output Level
Sets the output level
Src
e
Selects the modulation source for the output level
Amt
Sets the modulation amount of the output level
Gate - Threshold
Threshold
Louder
Input Level
Gate - Attack / Release
Threshold
Attack=1
Release=1
Attack=100
Release=100
Release
Attack
Mode: Overdrive / Hi-Gain
Drive
3 Band PEQ
Driver Amp Simulation
Wah
Output Level
Direct Mix
Toggle, Moment
Overdrive, Hi-Gain
Wet / Dry
Wet / Dry
Off, On
,
Off...Tempo
–10...+10
,
Off...Tempo
1...100
0...10
0...50
,
Off...Tempo
–50...+50