Korg Pa50 User Manual page 183

a: Frequency Bottom, a: Frequency Top
The sweep width and direction of the wah filter are deter-
mined by the "Frequency Top" and "Frequency Bottom"
settings.
Frequency
Top=75
Wah
Woo
Bottom=25
D
Higher
Zero Max
Frequency
Wah
Top=75
Woo
Woo
Bottom=25
Envelope
Time
b: Sweep Mode
This parameter changes the wah control mode. Setting
"Sweep Mode" to Auto will select an auto-wah that
sweeps according to envelope changes in the input signal
level. Auto-wah is frequently used for funk guitar parts
and clav sounds.
When "Sweep Mode" is set to D-mod, you can control the
filter directly via the modulation source in the same way
as a wah pedal.
When "Sweep Mode" is set to LFO, the effect uses LFO to
sweep in cycle.
c: Envelope Sens (Envelope Sensitivity)
This parameter sets the sensitivity of auto-wah. Increase
the value if the input signal is too low to sweep. Reduce
the value if the input signal is so high that the filter is
stopped temporarily.
c: Envelope Shape
This parameter determines the sweep curve for auto-wah.
Level
value = 0...+100
value = 0...–100
d: LFO Frequency [Hz], e: BPM/MIDI Sync
When "BPM/MIDI Sync"=Off, the LFO speed uses the LFO
Frequency parameter
Sync"=On, the LFO speed follows the "BPM", "Base
Note", and "Times" settings.
e: BPM, e: Base Note, e: Times
One cycle of LFO sweep is obtained by multiplying the
length of a note ( ... ) (selected for "Base Note", in rela-
tion to the tempo specified in ("BPM", or the MIDI Clock
tempo if "BPM" is set to MIDI) by the number specified in
the Times parameter.
Sweep Mode=D-mod
Frequency
Bottom=60
Wah
Woo
Top=30
-mod D -mod
Higher
Zero
Max
Sweep Mode=Auto
Frequency
Wah Wah
Bottom=75
Envelope
Top=25
Woo
Envelope Time
Envelope Shape
Envelope
Time
setting. When "BPM/MIDI
010: Random Filt
(Stereo Random Filter)
This stereo band pass filter uses a step-shape waveform and
random LFO for modulation. You can create a special effect
from filter oscillation.
Stereo In - Stereo Out
Left
Right
LFO: Step-Tri/Random
LFO Waveform
a
Selects LFO Waveform
LFO Phase [degree]
b
Sets the LFO phase difference between the left and right
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source used for both LFO speed and step speed
Amt
Sets the modulation amount of LFO speed
LFO Step Freq (Frequency) [Hz]
Sets the LFO step speed (speed that changes in steps)
d
Amt
Sets the modulation amount of LFO step speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
e
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Step Base Note
Selects the type of notes to specify the LFO step speed
f
Times
Sets the number of notes to specify the LFO step speed
Manual
g
Sets the filter center frequency
Depth
Sets the modulation depth of filter center frequency
Src
h
Selects the modulation source of filter modulation
Amt
Sets the modulation amount of filter modulation
Resonance
i
Sets the resonance amount
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
,
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: LFO Waveform, c: LFO Frequency [Hz],
d: LFO Step Freq (Frequency) [Hz]
When "LFO Waveform" is set to Step-Tri, LFO is a step-
shape, triangle waveform. The "LFO Frequency" parame-
ter sets the original triangle waveform speed. Changing
the "LFO Step Freq" parameter enables you to adjust the
width of the steps.
Effects 181
Filter/Dynamic
Wet / Dry
Filter
Filter
Wet / Dry
LFO Phase
Step-Tri, Random
–180...+180
0.02...20.00Hz
,
Off...Tempo
–20.00...+20.00Hz
0.05...50.00Hz
,
–50.00...+50.00Hz
Off, On
Fx:009,
MIDI, 40...240
Fx:009,
Fx:009
x1...x16
Fx:009
,
x1...x32
0...100
0...100
Off...Tempo
–100...+100
0...100
–Wet...–1:99, Dry, 1:99...Wet
Off...Tempo
–100...+100