Korg Pa50 User Manual page 179

Adjust the output level using the "Gain Adjust" parame-
ter, since compression causes the entire level to be
reduced.
Output Level
Threshold
Dry
Level
Ratio=Inf : 1
d: Attack, d: Release
These parameters set the attack time and release time. A
higher attack time will cause the compression to be
applied more slowly.
Dry
Wet
Wet
Attack
f: Side PEQ Insert, g: Side PEQ Cutoff [Hz], g: Q, g: Gain
[dB]
These parameters are used to set the EQ applied to the
trigger signal.
The Limiter determines whether the compression is
applied or not, based on the post-EQ trigger signal. Set-
ting the equalizer allows you to set the Limiter to respond
to any frequency band.
f: Trigger Monitor
Setting this parameter On will cause the trigger signal to
be output, instead of the effect sound. Use this parameter
to check the trigger signal with EQ applied.
Usually, set this to Off.
Limiter - Threshold / Ratio
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Ration=Inf : 1
Louder
Input Level
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Threshold
Time
Limiter - Attack / Release
Threshold
Ratio=Inf : 1
Attack=1
Release=1
Ratio=Inf : 1
Attack=100
Release=100
Release
004: MBandLimit
(Multiband Limiter)
This effect applies the Limiter to the low range, mid range,
and high range of the input signal. You can control dynamics
for each range to adjust the sound pressure of the low range,
mid range, and high range in a different way from the EQ.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Band-Pass Filters
Low
Envelope - Control
Mid Low Offset
+
Envelope - Control
Mid Offset
High
Envelope - Control
High Offset
Right
Ratio
a
Sets the signal compression ratio
Threshold [dB]
b
Sets the level above which the compressor is applied
Attack
c
Sets the attack time
Release
d
Sets the release time
Low Offset [dB]
e
Gain of the low-range trigger signal
Mid Offset [dB]
f
Gain of the mid-range trigger signal
High Offset [dB]
g
Gain of the high-range trigger signal
Gain Adjust [dB]
Sets the output gain
Src
h
Selects the modulation source for the output gain
Amt
Sets the modulation amount of the output gain
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
i
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
e: Low Offset [dB], f: Mid Offset [dB], g: High Offset [dB]
These parameters set the gain of the trigger signal.
For example, if you do not want to apply compression to
the high range, reduce the "High Offset" value down
below the "Threshold" level. In this way, the high range
limiter will not respond, and compression will not be
applied.
Effects 177
Filter/Dynamic
Wet / Dry
Limiter
Limiter
Gain Adjust
Limiter
Wet / Dry
1.0:1...50.0:1, Inf:1
Fx:003
–40...0dB
Fx:003
1...100
Fx:003
1...100
Fx:003
–40...0dB
–40...0dB
–40...0dB
–Inf, –38...+24dB
Fx:003,
Off...Tempo
–63...+63
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100